- 您現在的位置：買賣IC網 > PDF目錄11711 > DS2490S (Maxim Integrated Products)IC BRIDGE CLIP USB TO 1-W 24SOIC PDF資料下載
參數資料
| 型號： | DS2490S |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/50頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| 標準包裝： | 31 |
| 應用： | USB |
| 接口： | 1 線 |
| 電源電壓： | 3 V ~ 5.5 V |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS2490
22 of 50
Command parameters:
1 byte: Data byte to be sent to the 1-Wire bus. To read only, the byte
should be 0xFF.
EP2 data:
None, this command gets its input data as a command parameter.
EP3 data:
Length Description
If ICP = 0: 1 byte
Byte read back from the 1-Wire device.
If ICP = 1: None
No data is returned.
Result Register:
If ICP = 1: no result data is generated.
If ICP = 0 and NTF = 1: a result value of 0x00 will be generated.
If IPC = 0 and NTF = 0: no result data is generated since there are no
error codes associated with this command.
BLOCK I/O—This command accomplishes a direct 1-Wire write or read with optional strong pullup
after the last byte of the block. The optional strong pullup is controlled using embedded command bit
SPU. Embedded command bit RST enables a 1-Wire reset before the command executes. To accomplish
a READ function all input data should be 0xFF, otherwise the data read from the 1-Wire bus will be
masked. For a block write sequence the EP2 FIFO must be pre-filled with data before command
execution. Additionally, for block sizes greater then the FIFO size, the FIFO content status must be
monitored by host SW so that additional data can be sent to the FIFO when necessary. A similar EP3
FIFO content monitoring requirement exists for block read sequences. During a block read the number of
bytes loaded into the EP3 FIFO must be monitored so that the data can be read before the FIFO
overflows.
Command parameters:
2 bytes specifying block size.
EP2 data:
Length
Description
Same as block
size
Data block to be written to the 1-Wire device.
EP3 data:
Length
Description
Same as block
size
Data block read from the 1-Wire device.
Result Register:
If ICP = 1: no result data is generated.
If ICP = 0 and NTF = 1: a result value of 0x00 will be generated.
If IPC = 0 and NTF = 0: no result data is generated since there are no
error codes associated with this command.
MATCH ACCESS—This command is used to address a device on the active section of the 1-Wire bus
using the Match ROM or Overdrive Match command code. The EP2 FIFO must be pre-filled with the 8
bytes target ROM ID before command execution. Embedded command bit RST enables a 1-Wire reset
before the command executes, and embedded command bit SE enables a 1-Wire speed change that takes
effect before the command executes.
相關PDF資料 |
PDF描述 |
|---|---|
| V24B5H150BL2 | CONVERTER MOD DC/DC 5V 150W |
| D38999/26JD5PA | CONN PLUG 5POS STRAIGHT W/PINS |
| V24B5H150BF3 | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150B2 | CONVERTER MOD DC/DC 5V 150W |
| V24B48H150BL3 | CONVERTER MOD DC/DC 48V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2490S+ | 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Rail/Tube 制造商:Maxim Integrated Products 功能描述:USB 1-W BRIDGE CHIP 24-SO LF 制造商:Maxim Integrated Products 功能描述:Bulk |
| DS2490S+T&R | 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Tape and Reel |
| DS2490S+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip |
| DS2490X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB to 1-Wire Bridge Chip(468.41 k) |
| DS2490X/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。