- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2480B+ (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8-SOIC PDF資料下載
參數資料
| 型號： | DS2480B+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 23/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 線路驅動器，發(fā)射器 |
| 驅動器/接收器數： | 1/0 |
| 規(guī)程： | RS232 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2480B
Maxim Integrated............................................................................................................................................................................................. 3
As data enters the core of the DS2480B’s logic circuitry, it is analyzed to separate data and command
bytes and to calibrate the device’s timing generator. The timing generator controls all speed relations of
the communication interface and the 1-Wire bus as well as the waveforms on the 1-Wire bus.
Command bytes either affect the configuration setting or generate certain waveforms on the 1-Wire bus.
Data bytes are simply translated by the protocol converter into the appropriate 1-Wire activities. Each
data byte generates a return byte from the 1-Wire bus that is communicated back to the host through the
RXD pin as soon as the activity on the 1-Wire bus is completed.
The 1-Wire driver shapes the slopes of the 1-Wire waveforms, applies programming pulses or strong
pullup to 5V and reads the 1-Wire bus using a non-TTL threshold to maximize the noise margin for best
performance on large 1-Wire networks.
Figure 1. DS2480B BLOCK DIAGRAM
DEVICE OPERATION
The DS2480B can be described as a complex state machine with two static and several dynamic states.
Two device-internal flags as well as functions assigned to certain bit positions in the command codes
determine the behavior of the chip, as shown in the state transition diagram (Figure 2). The DS2480B
requires and generates a communication protocol of 8 data bits per character, 1 stop bit and no parity. It is
permissible to use 2 stop bits on the TXD line. However, the DS2480B only asserts a single stop bit on
RXD.
When powering up, the DS2480B performs a master reset cycle and enters the Command Mode, which is one of the two
static states. The device now expects to receive one 1-Wire reset command on the TXD line sent by the host at a data rate of
9600bps (see Communication Commands section for details). This command byte is required solely for calibration of the baud
rate timing generator the DS2480B and is not translated into any activity on the 1-Wire bus. After this first command byte the
device is ready to receive and execute any command as described later in this document. NOTE: Baud rate calibration is valid
only for the VDD operating voltage at which calibration is performed. Post-calibration changes in VDD by more than 5% may
cause calibration error to exceed ±5%. The DS2480B requires a 1-Wire reset command sent by the host at a data rate of
9600bps for calibration. Data rates of 115200bps or higher during calibration may put the DS2480B in an undefined state,
requiring a power-down reset to restore normal operation.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2480B | 制造商:Maxim Integrated Products 功能描述:IC SERIAL LINE DRIVER 2480 SOIC8 |
| DS2480B/T&R | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| DS2480B+ | 功能描述:緩沖器和線路驅動器 Serial - 1-Wire Line Driver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| DS2480B+R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
| DS2480B+T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Serial to 1-Wire Line Driver |
發(fā)布緊急采購，3分鐘左右您將得到回復。