- 您現在的位置：買賣IC網 > PDF目錄9756 > DS2450S (Maxim Integrated Products)IC CONVERTER A/D QUAD 1-W 8-SOIC PDF資料下載
參數資料
| 型號： | DS2450S |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONVERTER A/D QUAD 1-W 8-SOIC |
| 標準包裝： | 88 |
| 位數： | 16 |
| 采樣率（每秒）： | 1k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 輸入數目和類型： | 4 個單端，單極 |
DS2450
10 of 24
CONVERT [3CH]
The Convert command is used to initiate the analog to digital conversion for one or more channels at the
resolution specified in memory page 1, control/status data. The conversion takes between 60 and 80 μs
per bit plus an offset time of maximum 160 μs every time the convert command is issued. For four
channels with 12-bit resolution each, as an example, the convert command will not take more than
4x12x80 μs plus 160 μs offset, which totals 4 ms. If the DS2450 gets its power through the VCC pin, the
bus master may communicate with other devices on the 1-Wire bus while the DS2450 is busy with A/D
conversions. If the device is powered entirely from the 1-Wire bus, the bus master must instead provide a
strong pullup to 5V for the estimated duration of the conversion in order to provide sufficient energy.
The conversion is controlled by the input select mask (Figure 7a) and the read-out control byte (Figure
7b). In the input select mask the bus master specifies which channels participate in the conversion. A
channel is selected if the bit associated to the channel is set to 1. If more than one channel is selected, the
conversion takes place one channel after another in the sequence A, B, C, D, skipping those channels that
are not selected. The bus master can read the result of a channel’s conversion before the conversion of all
the remaining selected channels is completed. In order to distinguish between the previous result and the
new value the bus master uses the read-out control byte. This byte allows presetting the conversion read-
out registers for each selected channel to all 1’s or all 0’s. If the expected result is close to 0 then one
should preset to all 1’s or to all 0’s if the conversion result will likely be a high number. In applications
where the bus master can wait until all selected channels are converted before reading, a preset of the
read-out registers is not necessary. Note that for a channel not selected in the input select mask, the
channel’s read-out control setting has no effect. If a channel constantly yields conversion results close to
0 the channel’s output transistor may be conducting. See section Device Registers for details.
INPUT SELECT MASK (CONVERSION COMMAND)
Figure 7a
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
“don’t care”
D
C
B
A
READ-OUT CONTROL (CONVERSION COMMAND)
Figure 7b
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Set D
Clear D
Set C
Clear C
Set B
Clear B
Set A
Clear A
Set
Clear
Explanation
0
no preset, leave as is
0
1
preset to all 0’s
1
0
preset to all 1’s
1
(illegal code)
Following the Convert command byte the bus master transmits the input select mask and the read-out
control byte. Now the bus master reads the CRC16 of the command byte, select mask and control byte.
The conversion will start no earlier than 10 μs after the most significant bit of the CRC is received by the
bus master.
With a parasitic power supply the bus master must activate the strong pullup within this 10 μs window for
a duration that is estimated as explained above. After that, the data line returns to an idle high state and
communication on the bus can resume. The bus master would normally send a reset pulse to exit the
Convert command. Read data time slots generated after the strong pullup has ended but before issuing a
reset pulse should result in all 1’s if the conversion time was calculated correctly.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27656T21B11SA | CONN RCPT 11POS WALL MNT W/SCKT |
| 78P2352-IGT/F | IC LIU SDH SONET 2CH 128-LQFP |
| MC100E116FNR2G | IC LINE RECEIVER QUINT 28-PLCC |
| VE-26V-IU-F1 | CONVERTER MOD DC/DC 5.8V 200W |
| VE-26M-IU-F4 | CONVERTER MOD DC/DC 10V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2450S/T&R | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS2450S+ | 功能描述:模數轉換器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| DS2450S+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
| DS2450S+T&R | 制造商:Maxim Integrated Products 功能描述:IC CONVERTER A/D QUAD 1-W 8-SOIC |
| DS2450S+T&R | 功能描述:模數轉換器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。