- 您現在的位置：買賣IC網 > PDF目錄9755 > DS2181AN (Maxim Integrated Products)IC TXRX CEPT PRIM RATE IND 40DIP PDF資料下載
參數資料
| 型號： | DS2181AN |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/32頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX CEPT PRIM RATE IND 40DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 10 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CEPT |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-PDIP |
| 包裝： | 管件 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2181A
11 of 32
CCS SIGNALLING
CCS (selected when TCR.5 = 1 and/or when RCR.1 = 1) utilizes all bit positions of timeslot 16 in every
frame for message-oriented signaling data transmission. In CCS mode one can use either timeslot 16 or
any one of the other 30 data channels for message-oriented signaling. The CCS mode has no multiframe
structure and the insertion of CAS multiframe alignment, distant multiframe alarm and/or extra bits into
timeslot 16 is disabled. TSER is the source of timeslot 16 data.
CRC4 CODING
The need for enhanced error monitoring capability and additional protection against emulators of the
frame alignment word has led to the development of a cyclic redundancy check (CRC) procedure. When
enabled via CCR.2 and/or CCR.3, CRC4 coding replaces the international bit positions in frames 0
through 12 and 14 with a CRC4 multiframe alignment pattern and associated checksum words. The
CRC4 multiframe must begin with a frame containing the frame alignment signal (CCR.6 = 0). A rising
edge at TMSYNC establishes the CRC4 multiframe alignment (TMSYNC will also establish outgoing
CAS multiframe alignment if enabled via TCR.5).
Incoming CRC4 multiframe alignment is indicated by RCSYNC. Detected CRC4 checksum errors are re-
ported at output RFER and logged in the CECR.
RECEIVE SYNCHRONIZER
The fixed characteristics of the receive synchronizer may be modified by use of programmable
characteristics resident in the RCR and CCR. Sync criteria must be met before synchronization is
declared. Resync criteria establish error occurrences which will cause an auto-resync event when enabled
(RCR.1 = 0).
The receive synchronizer searches for the frame alignment pattern first. Once identified, the output timing
set associated with the framing pattern (all outputs except RCSYNC and RMSYNC) is updated to that
new alignment. If enabled, the synchronizer then begins CAS and/or CRC4 multiframe search; outputs
RMSYNC and/or RCSYNC are then updated. Output RLOS is held high during the entire resync process,
then transitions low after the last output timing update indicating resync is complete. For more details
about the receive synchronizer, see the separate DS2181A CEPT Transceiver Application Note.
FIXED FRAME SYNC CRITERIA
Valid frame sync is assumed when the correct frame alignment signal is present in frame N and frame N
+ 2 and not present in frame N + 1 (bit 2 of timeslot 0 of Frame N + 1 is also checked for 1). CAS and/or
CRC4 multiframe alignment search is initiated when the frame search is complete if enabled via RCR.5
and/or CCR.2.
FIXED CAS MULTIFRAME SYNC CRITERIA
CAS multiframe sync is declared when the multiframe alignment pattern is properly detected and timeslot
16 of the previous frame contains code other than zeros. If no valid pattern can be found in 12 to 14
milliseconds (no time-out period exists if CCR.1=1 or TEST=1), frame search is restarted.
FIXED CRC4 MULTIFRAME SYNC CRITERIA
CRC4 multiframe sync is declared if at least two valid CRC4 multiframe alignment signals are found
within 12 to 14 milliseconds (8 ms if CCR.1=1 or TEST=1) after frame alignment is completed. If not
found within 12 to 14 milliseconds (8 ms if CCR.1=1 or TEST=1), frame search is restarted. The search
for the multiframe alignment signal is performed in timeslot 0 of frames not containing the frame
alignment signal.
相關PDF資料 |
PDF描述 |
|---|---|
| MC10EP17DTR2 | IC RCVR/DRVR QUAD ECL DF 20TSSOP |
| DS26303LN-120+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| VE-26X-IU-F3 | CONVERTER MOD DC/DC 5.2V 200W |
| MC100EP17DTR2 | IC RCVR/DRV ECL QUAD DFF 20TSSOP |
| MX674AKN+ | IC ADC 12BIT W/REF 28-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2181AQ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2181AQ/T&R | 制造商:Maxim Integrated Products 功能描述:CEPT TRANCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TXRX CEPT PRIMARY RATE 44PLCC |
| DS2181AQ/T&R+ | 制造商:Maxim Integrated Products 功能描述:CEPT TRNSCVR 1TX 1RX 44PLCC - Tape and Reel |
| DS2181AQ/T&R | 功能描述:網絡控制器與處理器 IC CEPT Primary Rate Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2181AQ+ | 功能描述:網絡控制器與處理器 IC CEPT Primary Rate Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。