參數資料
型號： DS2180AN
廠商： Maxim Integrated Products
文件頁數： 33/35頁
文件大?。?/td> 0K
描述： IC TRANSCEIVER T1 IND 40-DIP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 10
功能： 收發器
接口： T1
電路數： 1
電源電壓： 4.5 V ~ 5.5 V
電流 - 電源： 3mA
工作溫度： -40°C ~ 85°C
安裝類型： 通孔
封裝/外殼： 40-DIP（0.600"，15.24mm）
供應商設備封裝： 40-PDIP
包裝： 管件
包括： 警報生成和檢測，B7 填充模式，B8ZS 模式，錯誤檢測和計數器，“硬件”模式，透明模式
DS2180A
7 of 35
ACB: ADDRESS COMMAND BYTE Figure 4
(MSB)
(LSB)
-
FRSR2
EYELMD
FM
SYELMD
B8ZS
B7
LPBK
SYMBOL
POSITION
NAME AND DESCRIPTION
-
CCR.7
Reserved, must be 0 for proper operation.
FRSR2
CCR.6
Function of REC Status Register 2.
0 = Detected B8ZS code words reported at RSR.2.
1 = COFA (Change-of-Frame Alignment) reported at RSR.2 when
last resync resulted in change of frame or multiframe alignment.
EYELMD
CCR.5
193E Yellow Mode Select.
0 = Yellow alarm is a repeating pattern set of 00 hex and FF hex.
1 = Yellow alarm is a 0 in the bit 2 position of all channels.
FM
CCR.4
Frame Mode Select.
0 = D4 (193S, 12 frames/superframe).
1 = Extended (193E, 24 frames/superframe).
SYELMD
CCR.3
193S Yellow Mode Select. Determines yellow alarm type to be
transmitted and detected while in 193S framing. If set, yellow
alarms are a 1 in the S-bit position of frame 12; if cleared, yellow
alarm is a 0 in bit 2 of all channels. Does not affect 193E yellow
alarm operation.
B8ZS
CCR.2
Bipolar eight zero substitution.
0 = No B8ZS.
1 = B8ZS enabled.
(Note: This bit must be set to 0 when CCR.1=1)
B7
CCR.1
Bit seven zero suppression. If CCR.1=1, channels with an all zero
content will be transmitted with bit 7 forced to 1. If CCR.1=0, no
bit 7 stuffing occurs.
(Note: This bit must be set to 0 when CCR.2=1)
LPBK
CCR.0
Loopback. When set, the device internally loops output transmit
data into the incoming receive data buffers and TCLK is internally
substituted for RCLK.
LOOPBACK (Refer to Figure 4)
Enabling loopback will typically induce an out-of-frame (OOF) condition. If appropriate bits are set in
the receive control register, the receiver will resync to the looped transmit frame alignment. During the
looped condition, the transmit outputs (TPOS, TNEG) will transmit unframed all 1's. All operating modes
(B8ZS, alarm, signaling, etc.) except for blue alarm transmission are available in loopback.
BIT SEVEN STUFFING
Existing systems meet 1's density requirements by forcing bit 7 of all zero channels to 1. Bit 7 stuffing is
globally enabled by asserting bit CCR.1 and may be disabled on an individual channel basis by setting
appropriate bits in TTR1–TTR3. Bit 7 stuffing and B8ZS modes should not be enabled simultaneously.
Enabling both results in LOS.
相關PDF資料
PDF描述
DS2180AQ/T&R IC TRANSCEIVER T1 44-PLCC
DS2180AQ+T&R IC TRANSCEIVER T1 44-PLCC
VI-2VY-IX-F4 CONVERTER MOD DC/DC 3.3V 49.5W
DS2172T+T&R IC TESTER BIT ERROR RATE 32-TQFP
VI-2VY-IX-F3 CONVERTER MOD DC/DC 3.3V 49.5W
相關代理商/技術參數
參數描述
DS2180AQ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ/T&R 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver
DS2180AQ/T&R+ 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel
DS2180AQ/T&R 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ+ 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*