- 您現在的位置：買賣IC網 > PDF目錄1914 > DS2118MB+T&R (Maxim Integrated Products)IC TERM SCSI LVD/SE ULT-3 36SSOP PDF資料下載
參數資料
| 型號： | DS2118MB+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TERM SCSI LVD/SE ULT-3 36SSOP |
| 標準包裝： | 1,000 |
| 類型： | SCSI，LVD，SE |
| 端子數： | 9 |
| 電源電壓： | 4 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-BSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
DS2118M
3 of 10
FUNCTIONAL DESCRIPTION
The DS2118 combines LVD and SE termination with DIFFSENSE sourcing and detection.
A bandgap reference is fed into two amplifiers, which creates a 1.25V reference voltage and a 2.85V
reference voltage. The control logic determines which of these references will be applied to the
termination resistors. If the SCSI bus is in LVD mode, then the 1.25V reference will be used. If the SCSI
bus is in SE mode, then the 2.85V reference will be used. That same control logic will switch in/out
parallel resistors to change the total termination resistance accordingly. Finally, in SE mode the Rp pins
will be switched to ground.
The DIFFSENSE circuitry decodes trinary logic. There will be one of three voltages on the SCSI control
line called DIFFSENS. Two comparators and a NAND gate determine if the voltage is below 0.6V, above
2.15V, or in between. That indicates the mode of the bus to be HVD, SE, or LVD, respectively.
The DS2118M’s DIFF_CAP pin monitors the DIFFSENS line to determine the proper operating mode of
the device; this mode is indicated by the SE/LVD/HVD outputs. The DIFFSENSE pin can also drive the
SCSI DIFFSENS line (when MSTR/SLV = 1) to determine the SCSI bus operating mode. The DS2118M
switches to the termination mode that is appropriate for the bus based on the value of the DIFFSENS
voltage. These modes are:
LVD Mode: LVD termination is provided by a precision laser-trimmed resistor string with two
amplifiers. This configuration yields a 105 differential and 150
common-mode impedance. A
fail-safe bias of 112mV is maintained when no drivers are connected to the SCSI bus.
SE Mode: When the external driver for a given signal line turns off, the active terminator will
pull that signal line to 2.85V (quiescent state). When used with an active negation driver, the
power amp can sink 22mA per line while keeping the voltage reference in regulation. The
terminating resistors maintain their 110
value.
HVD Isolation Mode: The DS2118M identifies that there is an HVD (high-voltage differential)
device on the SCSI bus and isolates the termination pins from the bus.
When ISO is pulled high, the termination pins are isolated from the SCSI bus, VREF remains active, and
the bus mode indicators (SE/LVD/HVD) remain active. During thermal shutdown, the termination pins
are isolated from the SCSI bus, VREF becomes high impedance, and the bus mode indicators
(SE/LVD/HVD) remain active. The DIFFSENSE driver is shut down during either of these two events.
An internal pulldown resistor assures that the DS2118M will be terminating the bus if the ISO pin is left
floating.
To ensure proper operation, the TPWR pin should be connected to the SCSI bus TERMPWR line. As
with all analog circuitry, the TERMPWR and VDD lines should be bypassed locally. A 2.2F capacitor
and a 0.01
F high-frequency capacitor is recommended between TPWR and ground and placed as close
as possible to the DS2118M. The DS2118M should be placed as close as possible to the SCSI connector
to minimize signal and power-trace length, thereby resulting in less input capacitance and reflections,
which can degrade the bus signals.
To maintain the specified regulation, a 4.7
F capacitor is required between the VREF pin (VREF) and
ground of each DS2118M. A high frequency cap (0.1
F ceramic recommended) can also be placed on the
相關PDF資料 |
PDF描述 |
|---|---|
| DS2119ME+T&R | IC TERM SCSI LVD/SE ULT3 28TSSOP |
| DS2125+T&R | IC TERM SCSI ULT3 LVD/SE 48-LQFP |
| DS2127+T&R | IC TERM SCSI LVD/SE 48-LQFP |
| DS21348T | IC LIU T1/E1/J1 3.3V 44-TQFP |
| DS21349Q+ | IC LIU T1/J1 3.3V 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2119M | 功能描述:IC TERM SCSI LVD/SE ULT3 28TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| DS2119M/T&R | 制造商:Maxim Integrated Products 功能描述:IC TERM SCSI LVD/SE ULT3 28TSSOP |
| DS2119M/T&R | 功能描述:IC TERM SCSI LVD/SE ULT3 28TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| DS2119ME | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS2119ME/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC TERM SCSI LVD/SE ULT3 28TSSOP |
發布緊急采購，3分鐘左右您將得到回復。