- 您現在的位置：買賣IC網 > PDF目錄97865 > DS18S20Z/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS18S20Z/T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | SOP-8 |
| 文件頁數： | 6/23頁 |
| 文件大?。?/td> | 252K |
| 代理商： | DS18S20Z/T&R |
DS18S20
14 of 23
READ-TIME SLOTS
The DS18S20 can only transmit data to the master when the master issues read-time slots. Therefore, the
master must generate read-time slots immediately after issuing a Read Scratchpad [BEh] or Read Power
Supply [B4h] command, so that the DS18S20 can provide the requested data. In addition, the master can
generate read-time slots after issuing Convert T [44h] or Recall E
2 [B8h] commands to find out the status
of the operation as explained in the DS18S20 Function Commands section.
All read-time slots must be a minimum of 60
s in duration with a minimum of a 1s recovery time
between slots. A read-time slot is initiated by the master device pulling the 1-Wire bus low for a
minimum of 1
s and then releasing the bus (see Figure 11). After the master initiates the read-time slot,
the DS18S20 will begin transmitting a 1 or 0 on bus. The DS18S20 transmits a 1 by leaving the bus high
and transmits a 0 by pulling the bus low. When transmitting a 0, the DS18S20 will release the bus by the
end of the time slot, and the bus will be pulled back to its high idle state by the pullup resister. Output
data from the DS18S20 is valid for 15
s after the falling edge that initiated the read-time slot. Therefore,
the master must release the bus and then sample the bus state within 15
s from the start of the slot.
Figure 12 illustrates that the sum of TINIT, TRC, and TSAMPLE must be less than 15s for a read-time slot.
Figure 13 shows that system timing margin is maximized by keeping TINIT and TRC as short as possible
and by locating the master sample time during read-time slots towards the end of the 15
s period.
Figure 11. Read/Write Time Slot Timing Diagram
45
s
15
s
VPU
GND
1-WIRE BUS
60
s < T
X “0” < 120 s
1
s < T
REC <
∞
DS18S20 Samples
MIN
TYP
MAX
15
s
30
s
> 1
s
MASTER WRITE “0” SLOT
MASTER WRITE “1” SLOT
VPU
GND
1-WIRE BUS
15
s
MASTER READ “0” SLOT
MASTER READ “1” SLOT
Master samples
START
OF SLOT
START
OF SLOT
> 1
s
1
s < T
REC <
∞
15
s
15
s
30
s
15
s
DS18S20 Samples
MIN
TYP
MAX
> 1
s
LINE TYPE LEGEND
Bus master pulling low
DS18S20 pulling low
Resistor pullup
相關PDF資料 |
PDF描述 |
|---|---|
| DS1963L-F5 | SPECIALTY MEMORY CIRCUIT, MEDB2 |
| DS1963S | SPECIALTY MEMORY CIRCUIT, MEDB2 |
| DS1985-F3 | 2K X 8 EEPROM 3V, RDB2 |
| DS1986-F3 | 64K X 1 OTPROM, MEDB2 |
| DS1986-F5 | 64K X 1 OTPROM, MADB2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS18VN6LPQ | 制造商:Banner Engineering 功能描述:SENSOR, PHOTOELECTRIC, DS18VN6LPQ PICO QP NPN POL RET |
| DS18VP6FF50Q8 | 制造商:Banner Engineering 功能描述:DS18VP6FF50Q8 EURO QD PNP 50MM FIXED FIELD |
| DS18VP6LP-29537 | 制造商:Banner Engineering 功能描述:DS18 Series: Polarized Retro, Range: 3.5 m, Input: 10-30V dc, Output: Complement |
| DS18VP6LPQ8 | 制造商:Banner Engineering 功能描述:SENSOR, PHOTOELECTRIC, DS18VP6LPQ8 EURO QD PNP POL RETRO |
| DS1904 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Real-Time Clock/calendar in binary format RTC iButton Over 10 years of operation |
發布緊急采購，3分鐘左右您將得到回復。