- 您現在的位置：買賣IC網 > PDF目錄9056 > DS1866 (Maxim Integrated Products)IC POT TRIM LOG 2.7-5.5V 8-DIP PDF資料下載
參數資料
| 型號： | DS1866 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT TRIM LOG 2.7-5.5V 8-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 接片： | 8 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 3 輸入并口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
DS1866
5 of 5
102199
NOTES:
1. All voltages are referenced to ground.
2. For VCC = 5V ± 10% maximum VIL = +0.8V. For VCC 3.0 ± 10% VIL = +0.6V. For VCC =2.7 volts VIH
=2.0 volts minimum.
3. Resistor input voltages cannot go below ground or exceed VCC by the amounts as shown in the table.
4. Maximum current specifications are based on the change rate of the parallel port inputs P0, P1, and
P2.
5. Standby current specifications apply when P0, P1, P2 logic inputs are driven within the specified VIH
or VIL levels.
6. Valid at 25
°C only.
7. The end-to-end resistance tolerance of the DS1866 can be expected to shift with temperature.
However, this change will not exceed ±20% of the nominal resistor value of the part.
8. Absolute tolerance is used to compare measured wiper voltage versus expected wiper voltage as
determined by wiper position. The DS1866 is specified to provide an absolute tolerance of ±1.0 dB.
9. Tap-to-tap tolerance is used to determine the change in voltage between successive tap positions. The
DS1866 is specified to provide a tap-to-tap tolerance specification of ±1.0 dB.
10. -3 dB cutoff frequency characteristic for the DS1866 is 1 MHz.
11. Capacitance values apply at 25°C.
12. This specification refers to the time difference between parallel port input changes to stabilize a wiper
transition.
DS1866 ORDERING INFORMATION
ORDERING NUMBER
PACKAGE
OPERATING
TEMPERATURE
VERSION
DS1866
8L DIP
-40°C TO +85°C
10k
DS1866Z
8L SOIC (150-MIL)
-40°C TO +85°C
10k
相關PDF資料 |
PDF描述 |
|---|---|
| DS1809-010 | IC DALLASTAT 10K 300MIL 8-DIP |
| MS3456L24-12PW | CONN PLUG 5POS STRAIGHT W/PINS |
| DS1844E-100/T&R | IC POT DIG QUAD 100K 20-TSSOP |
| MS3456L24-12P | CONN PLUG 5POS STRAIGHT W/PINS |
| DS1868S-050/T&R | IC POT DIGITAL DUAL 50K 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1866+ | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1866N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866SN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| DS1866Z | 功能描述:數字電位計 IC Log Trimmer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。