- 您現在的位置：買賣IC網 > PDF目錄295504 > DS1845X-100 (DALLAS SEMICONDUCTOR) 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 PDF資料下載
參數資料
| 型號： | DS1845X-100 |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | 數字電位計 |
| 英文描述： | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 |
| 封裝： | FCP-14 |
| 文件頁數： | 7/13頁 |
| 文件大小： | 98K |
| 代理商： | DS1845X-100 |
DS1845
3 of 13
H0, H1 – These are the high-end terminals of the potentiometers. For both potentiometers, it is not
required that these terminals be connected to a potential greater than the low-end terminal of the
potentiometer. Voltage applied to the high end of the potentiometers cannot exceed the power supply
voltage, VCC, or go below ground.
L0, L1 – These are the low-end terminals of the potentiometers. It is not required that these terminals be
connected to a potential less than the high-end terminals of the pot. Voltage applied to the low end of the
potentiometers cannot exceed the power-supply voltage, VCC, or go below ground.
W0, W1 - Wiper of the Potentiometer. This pin is the wiper terminal of the potentiometer. The bytes in
EEPROM memory locations F8h and F9h determine each wiper’s setting. Voltage applied to either
wiper terminal cannot exceed the power-supply voltage, VCC, or go below ground.
MEMORY ORGANIZATION
The DS1845’s serial EEPROM is internally organized with 256 words of 1 byte each. Each word requires
an 8-bit address for random word addressing. The byte at address F9h determines the wiper setting for
potentiometer 0, which contains 100 positions. Writing values above 63h to this address sets the wiper to
its uppermost position. The byte at address F8h determines the wiper setting for potentiometer 1, which
contains 256 positions (00h to FFh). Address locations FAh though FFh are reserved and should not be
written.
DEVICE OPERATION
Clock and Data Transitions: The SDA pin is normally pulled high with an external resistor or device.
Data on the SDA pin may only change during SCL low time periods. Data changes during SCL high
periods will indicate a start or stop conditions depending on the conditions discussed below. Refer to the
timing diagram Fig 2 for further details.
Start Condition: A high-to-low transition of SDA with SCL high is a start condition which must
precede any other command. Refer to the timing diagram Fig 2 for further details.
Stop Condition: A low-to-high transition of SDA with SCL high is a stop condition. After a read
sequence, the stop command places the DS1845 into a low-power mode. Refer to the timing diagram Fig
2 for further details.
Acknowledge: All address and data byte are transmitted via a serial protocol. The DS1845 pulls the
SDA line low during the ninth clock pulse to acknowledge that it has received each word.
Standby Mode: The DS1845 features a low-power mode that is automatically enabled after power-on,
after a stop command, and after the completion of all internal operations.
2-Wire Interface Reset: After any interruption in protocol, power loss, or system reset, the following
steps reset the DS1845.
1. Clock up to nine cycles.
2. Look for SDA high in each cycle while SCL is high.
3.
Create a start condition while SDA is high.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1866N | DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDIP8 |
| DS1867-100-IND | 100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
| DS2009D-65 | 512 X 9 OTHER FIFO, 65 ns, PDIP28 |
| DS500008-12 | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| DS80C310-MCL | 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1845X-100/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT & MEM BUMP 10K/100K TR - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC POT/MEM DUAL NV 100K 14-FCP |
| DS1845X-100/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1846 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:NV Tri-Potentiometer, Memory, and MicroMonitor |
| DS1846E-010 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1846E-010/R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:NV Tri-Potentiometer, Memory, and MicroMonitor |
發布緊急采購，3分鐘左右您將得到回復。