- 您現在的位置：買賣IC網 > PDF目錄295504 > DS17885N-3 (MAXIM INTEGRATED PRODUCTS INC) 1 TIMER(S), REAL TIME CLOCK, PDIP24 PDF資料下載
參數資料
| 型號： | DS17885N-3 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | XO, clock |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDIP24 |
| 封裝： | DIP-24 |
| 文件頁數： | 4/38頁 |
| 文件大?。?/td> | 410K |
| 代理商： | DS17885N-3 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
DS17885/DS17887
12 of 38
NV RAM–RTC
The general-purpose NV RAM bytes are not dedicated to any special function within the
DS17885/DS17887. They can be used by the application program as nonvolatile memory and are fully
available during the update cycle.
The user RAM is divided into two separate memory banks. When the bank 0 is selected, the 14 real-time
clock registers and 114 bytes of user RAM are accessible. When bank 1 is selected, an additional 4kB of
user RAM are accessible through the extended RAM address and data registers.
INTERRUPT CONTROL
The DS17885/DS17887 includes six separate, fully automatic sources of interrupt for a processor:
1) Alarm Interrupt
2) Periodic Interrupt
3) Update-Ended Interrupt
4) Wake-Up Interrupt
5) Kickstart Interrupt
6) RAM Clear Interrupt
The conditions that generate each of these independent interrupt conditions are described in greater detail
elsewhere in this data sheet. This section describes the overall control of the interrupts.
The application software can select which interrupts, if any, should be used. There are 6 bits including 3
bits in Register B and 3 bits in Extended Register 4B that enable the interrupts. The extended register
locations are described later. Writing a logic 1 to an interrupt-enable bit permits that interrupt to be
initiated when the event occurs. A logic 0 in the interrupt-enable bit prohibits the IRQ pin from being
asserted from that interrupt condition. If an interrupt flag is already set when an interrupt is enabled, IRQ
is immediately be set at an active level, even though the event initiating the interrupt condition may have
occurred much earlier. As a result, there are cases where the software should clear these earlier generated
interrupts before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is set to a logic 1 in Register C or in Extended
Register 4A. These flag bits are set regardless of the setting of the corresponding enable bit located either
in Register B or in Extended Register 4B. The flag bits can be used in a polling mode without enabling
the corresponding enable bits.
However, care should be taken when using the flag bits of Register C because they are automatically
cleared to 0 immediately after they are read. Double latching is implemented on these bits so that bits that
are set remain stable throughout the read cycle. All bits that were set are cleared when read and new
interrupts that are pending during the read cycle are held until after the cycle is completed. 1 bit, 2 bits, or
3 bits can be set when reading Register C. Each used flag bit should be examined when read to ensure
that no interrupts are lost.
The flag bits in Extended Register 4A are not automatically cleared following a read. Instead, each flag
bit can be cleared to 0 only by writing 0 to that bit.
When using the flag bits with fully enabled interrupts, the IRQ line is driven low when an interrupt flag
bit is set and its corresponding enable bit is also set. IRQ is held low as long as at least one of the six
相關PDF資料 |
PDF描述 |
|---|---|
| DS1806S-050-IND | 50K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDSO20 |
| DS1845X-010 | 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 |
| DS1845X-100 | 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, UUC14 |
| DS1866N | DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 64 POSITIONS, PDIP8 |
| DS1867-100-IND | 100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDIP14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17885N-5 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock |
| DS17885S-3 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17885S-3+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17885S-5 | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17885S-5/T&R+ | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK MULTIPLEXED 8KBYTE 24SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC 5V 8K NV RAM 24-SOIC |
發布緊急采購，3分鐘左右您將得到回復。