- 您現在的位置：買賣IC網 > PDF目錄1993 > DS1394U-33+T&R (Maxim Integrated Products)IC RTC SPI 3WIRE W/CHRGR 10-MSOP PDF資料下載
參數資料
| 型號： | DS1394U-33+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/26頁 |
| 文件大小： | 0K |
| 描述： | IC RTC SPI 3WIRE W/CHRGR 10-MSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，方波輸出，涓流充電器 |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | SPI |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 帶卷 (TR) |
DS1390–DS1394
Low-Voltage SPI/3-Wire RTCs with
Trickle Charger
17
Maxim Integrated
Bit 7: Enable Oscillator (
EOSC). When set to logic 0,
this bit starts the oscillator. When this bit is set to logic
1, the oscillator is stopped whenever the device is pow-
ered by VBACKUP. The oscillator is always enabled
when VCC is valid. This bit is enabled (logic 0) when
VCC is first applied.
Bit 5: Battery-Backed Square-Wave and Interrupt
Enable (BBSQI). This bit when set to logic 1 enables the
square wave or interrupt output when VCC is absent and
the DS1390/DS1392/DS1393/DS1394 are being pow-
ered by the VBACKUP pin. When BBSQI is logic 0, the
SQW/INT pin (or SQW and INT pins) goes high imped-
ance when VCC falls below the power-fail trip point. This
bit is disabled (logic 0) when power is first applied.
Bits 4 and 3: Rate Select (RS2 and RS1). These bits
control the frequency of the square-wave output when
the square wave has been enabled. The table below
shows the square-wave frequencies that can be select-
ed with the RS bits. These bits are both set to logic 1
(32kHz) when power is first applied.
Bit 2: Interrupt Control (INTCN). This bit controls the
SQW/INT signal. When the INTCN bit is set to logic 0, a
square wave is output on the SQW/INT pin. The oscilla-
tor must also be enabled for the square wave to be out-
put. When the INTCN bit is set to logic 1, a match
between the timekeeping registers and either of the
alarm registers then activates the SQW/INT (provided
the alarm is also enabled). The corresponding alarm
flag is always set, regardless of the state of the INTCN
bit. The INTCN bit is set to logic 0 when power is first
applied.
Bit 0: Alarm Interrupt Enable (AIE). When set to logic
1, this bit permits the alarm flag (AF) bit in the status
register to assert SQW/INT (when INTCN = 1). When
the AIE bit is set to logic 0 or INTCN is set to logic 0,
the AF bit does not initiate the SQW/INT signal. The AIE
bit is disabled (logic 0) when power is first applied.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
EOSC
0
BBSQI
RS2
RS1
INTCN
0
AIE
Control Register (0D/8Dh) (DS1390/DS1393/DS1394 Only)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
EOSC
0X
X
0X
Control Register (0D/8Dh) (DS1391 Only)
RS2
RS1
SQUARE-WAVE OUTPUT FREQUENCY
0
1Hz
0
1
4.096kHz
1
0
8.192kHz
1
32.768kHz
Special-Purpose Registers
The DS1390–DS1394 have three additional registers
(control, status, and trickle charger) that control the
RTC, alarms, square-wave output, and trickle charger.
Control bits used in the DS1390 become general-pur-
pose, battery-backed, nonvolatile SRAM bits in the
DS1391.
相關PDF資料 |
PDF描述 |
|---|---|
| DS14285SN+T&R | IC RTC W/NV RAM CNTRL 24-SOIC |
| DS1486P-120+ | IC TIMEKEEPER RAM 1MB 34-PCM |
| DS1500WE | IC RTC Y2KC W/NV CTRL 32-TSOP |
| DS1501YSN+T&R | IC RTC WDOG Y2K 5V IND 28-SOIC |
| DS1553P-70+ | IC RTC RAM Y2K 5V 70NS 34-PCM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1395 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Real Time Clock |
| DS1395N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| DS1395S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Real Time Clock |
| DS1395SN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| DS1397 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Real Time Clock |
發布緊急采購，3分鐘左右您將得到回復。