- 您現在的位置：買賣IC網 > PDF目錄9142 > DS1087LU-266+ (Maxim Integrated Products)IC ECONOSCILLATOR SS 8-USOP PDF資料下載
參數資料
| 型號： | DS1087LU-266+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ECONOSCILLATOR SS 8-USOP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 系列： | EconOscillator™ |
| 類型： | 時鐘發生器 |
| PLL： | 無 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 66MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 2.7 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
DS1087L
3.3V Spread-Spectrum EconOscillator
10
____________________________________________________________________
Data valid: The state of the data line represents
valid data when, after a START condition, the data
line is stable for the duration of the HIGH period of
the clock signal. The data on the line must be
changed during the LOW period of the clock sig-
nal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condi-
tion and terminated with a STOP condition. The
number of data bytes transferred between START
and STOP conditions is not limited, and is deter-
mined by the master device. The information is
transferred byte-wise and each receiver acknowl-
edges with a ninth bit.
Within the bus specifications a standard mode
(100kHz clock rate) and a fast mode (400kHz
clock rate) are defined. The DS1087L works in
both modes.
Acknowledge: Each receiving device, when
addressed, is obliged to generate an acknowl-
edge after the byte has been received. The master
device must generate an extra clock pulse that is
associated with this acknowledge bit.
A device that acknowledges must pull down the
SDA line during the acknowledge clock pulse in
such a way that the SDA line is stable LOW during
the HIGH period of the acknowledge-related clock
pulse. Of course, setup and hold times must be
taken into account. When the DS1087L EEPROM
is being written to, it is not able to perform addi-
tional responses. In this case, the slave DS1087L
sends a not acknowledge to any data transfer
request made by the master. It resumes normal
operation when the EEPROM operation is com-
plete.
A master must signal an end of data to the slave
by not generating an acknowledge bit on the last
byte that has been clocked out of the slave. In this
case, the slave must leave the data line HIGH to
enable the master to generate the STOP condition.
Figures 3, 4, 5, and 6 detail how data transfer is
accomplished on the 2-wire bus. Depending upon
the state of the R/
W bit, two types of data transfer
are possible:
1)
Data transfer from a master transmitter to a slave
receiver. The first byte transmitted by the master is
the slave address. Next follows a number of data
bytes. The slave returns an acknowledge bit after
each received byte.
2)
Data transfer from a slave transmitter to a master
receiver. The first byte (the slave address) is trans-
mitted by the master. The slave then returns an
acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The
master returns an acknowledge bit after all
received bytes other than the last byte. At the end
of the last received byte, a not acknowledge is
returned.
The master device generates all the serial clock
pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a
repeated START condition. Since a repeated
START condition is also the beginning of the next
serial transfer, the bus is not released.
The DS1087L can operate in the following two modes:
Slave receiver mode: Serial data and clock are
received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted.
START and STOP conditions are recognized as
the beginning and end of a serial transfer.
Address recognition is performed by hardware
after reception of the slave address and direction
bit.
Slave transmitter mode: The first byte is received
and handled as in the slave receiver mode.
However, in this mode, the direction bit indicates
that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1087L while the
serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and
end of a serial transfer.
Slave Address
Figure 4 shows the first byte sent to the device. It
includes the device identifier, device address, and the
R/
W bit. The device address must match the address
set in the ADDR register (bits A0, A1, and A2).
Registers/Commands
See Table 1 for the complete list of registers/com-
mands and Figure 6 for an example of using them.
MSB
DEVICE
IDENTIFIER
DEVICE
ADDRESS
READ/WRITE
BIT
1
0
1
A2
A1
A0
R/W
LSB
Figure 4. Slave Address
相關PDF資料 |
PDF描述 |
|---|---|
| V375B12H300B | CONVERTER MOD DC/DC 12V 300W |
| VI-233-MW-S | CONVERTER MOD DC/DC 24V 100W |
| MAX9485EUP+ | IC CLOCK GEN PROG 20TSSOP |
| V375B15H300BG3 | CONVERTER MOD DC/DC 15V 300W |
| VI-232-MW-S | CONVERTER MOD DC/DC 15V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1087LU-266/T&R | 制造商:Maxim Integrated Products 功能描述:3V SS OSC 66.66 MHZ 2% DWN 8USOP TR - Tape and Reel |
| DS1087LU-266/T&R | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1087LU-266+ | 功能描述:計時器和支持產品 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS1087LU-266+T&R | 制造商:Maxim Integrated Products 功能描述:3V SS OSC 66.66MHZ 2% DOWN 8U TR LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC ECONOSCILLATOR SS 8-USOP |
| DS1087LU-266+T&R | 功能描述:可編程振蕩器 3.3V Spread-Spectrum EconOscillator RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
發布緊急采購，3分鐘左右您將得到回復。