- 您現在的位置：買賣IC網 > PDF目錄2067 > DS1085Z-25+ (Maxim Integrated Products)IC ECONOSCILLATOR SYNTH 8-SOIC PDF資料下載
參數資料
| 型號： | DS1085Z-25+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/21頁 |
| 文件大小： | 0K |
| 描述： | IC ECONOSCILLATOR SYNTH 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 系列： | EconOscillator™ |
| 類型： | 頻率合成器 |
| PLL： | 無 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 133MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
DS1085
10 of 21
COMMAND SET
Data and control information is read from and written to the DS1085 in the format shown in Figure 3. To
write to the DS1085, the master issues the slave address of the DS1085 and the R/ W bit is set to 0. After
receiving an acknowledge, the bus master provides a command protocol. After receiving this protocol, the
DS1085 issues an acknowledge, and then the master can send data to the DS1085. If the DS1085 is to be
read, the master must send the command protocol as before, and then issue a repeat START condition and
then the control byte again, this time with the R/ W bit set to 1 to allow reading of the data from the
DS1085. The command set for the DS1085 is as follows:
Access DAC [08h]
If R/ W is 0, this command writes to the DAC register. After issuing this command, the next data byte
values are written into the DAC register. If R/ W is 1, the next data bytes read are the values stored in the
DAC register. This is a 2-byte transfer, the first byte contains the eight MSBs, the second byte contains
the two LSBs in the most significant positions of the data byte. The remaining six bits are ignored and
can be written with any value (if read, these bits are 0).
Access OFFSET [0Eh]
If R/ W is 0, this command writes to the OFFSET register. After issuing this command, the next data byte
value is written into the OFFSET register. If R/ W is 1, the next data byte read is the value stored in the
OFFSET register. This is a single byte transfer of which only the five LSBs (last five bits) are used. The
remaining three bits can be written with any value to complete the data byte (if read, these bits are 1).
Access DIV [01h]
If R/ W is 0, this command writes to the DIV register. After issuing this command, the next data byte
values are written into the DIV register. If R/ W is 1, the next data bytes read are the values stored in the
DIV register. This register has a 10-bit value. The upper eight bits are sent first, followed by a second
byte that contains the two LSBs of the register value in the most significant positions of the data byte.
The remaining six bits are ignored and can be set to any value (if read, these bits are 0).
Access MUX [02h]
If R/ W is 0, this command writes to the MUX register. After issuing this command, the next data byte
values are written into the MUX register. If R/ W is 1, the next data bytes read are the values stored in the
MUX register. This register has a 10-bit value. The upper eight bits are sent first, followed by a second
byte that contains the two LSBs of the register value in the most significant positions of the data byte.
The remaining six bits are ignored and can be set to any value (if read, these bits are 0).
Access ADDR [0Dh]
If R/ W is 0, this command writes to the ADDR register. After issuing this command, the next data byte
value is written into the ADDR register. If R/ W is 1, the next data byte read is the value stored in the
ADDR register. This is a single-byte transfer. This register has a 5-bit value, the first three bits of a write
can be any value followed by the five active bits (if read, the first three bits are 0).
相關PDF資料 |
PDF描述 |
|---|---|
| DS1086HU-C02+ | IC ECONOSCILLATOR SS 8-USOP |
| DS1086LU-222+ | IC CLK GEN 22.1184MHZ AUTO 8USOP |
| DS1087LU-2CL+ | IC ECONOSCILLATOR SS 3.6V 8-MSOP |
| DS1088LU-02A+W | IC ECONOSCILL 2.048MHZ 8USOP |
| DS1089LU-C29+W | IC ECONOSCILL 3.3V SS 8-USOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1085Z-25+ | 功能描述:可編程振蕩器 EconOscillator f Synthesizer RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1085Z-50 | 功能描述:可編程振蕩器 EconOscillator f Synthesizer RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1085Z-50+ | 功能描述:可編程振蕩器 EconOscillator f Synthesizer RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1086 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:DS1086 Spread-Spectrum EconOscillator |
| DS1086_1203 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Spread-Spectrum EconOscillator |
發布緊急采購，3分鐘左右您將得到回復。