- 您現在的位置：買賣IC網 > PDF目錄97857 > DS1077Z-66 (DALLAS SEMICONDUCTOR) 66.666 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF資料下載
參數資料
| 型號： | DS1077Z-66 |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Clock Generator |
| 英文描述： | 66.666 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封裝： | 0.150 INCH, SOIC-8 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 103K |
| 代理商： | DS1077Z-66 |
DS1077
9 of 17
DATA TRANSFER ON 2-WIRE SERIAL BUS (Figure 2)
MSB
slave address
R/W
direction
bit
SDA
SCL
START
CONDITION
12
678
9
12
8
9
STOP CONDITION
OR
REPEATED
START CONDITION
3 - 8
acknowledgement
signal from receiver
acknowledgement
signal from receiver
ACK
repeated if more bytes
are transferred
Figure 2 details how data transfer is accomplished on the two-wire bus. Depending upon the state of the
R/W* bit, two types of data transfer are possible:
1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte.
2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a 'not acknowledge' is returned.
The master device generates all of the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START
condition is also the beginning of the next serial transfer, the bus will not be released.
The DS1077 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception
of the slave address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode, the direction bit will indicate that the transfer direction is reversed. Serial
data is transmitted on SDA by the DS1077 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1077Z-125 | 125 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1077Z-100 | 100 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| DS1100U-175/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-40/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
| DS1100U-45/T&R | SILICON DELAY LINE, TRUE OUTPUT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1077Z-66+ | 功能描述:可編程振蕩器 EconOscillator/Dvdr 66MHz 118mil 2-Wire RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS10-80B | 制造商:TRANSMISSION DEVELOPMENTS 功能描述:MOULDED SPUR GEAR 1.0, 80 |
| DS1080CL | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Spread-Spectrum Crystal Multiplier |
| DS1080CLU+ | 功能描述:時鐘發生器及支持產品 Spread-Spectrum Crystal Multiplier RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| DS1080CLU+T | 功能描述:時鐘發生器及支持產品 Spread-Spectrum Crystal Multiplier RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。