Figure 11. 32k Point FFT with fIN = 2kHz of the LTC2378-18" />
參數資料
型號： DC1783A-F
廠商： Linear Technology
文件頁數： 6/24頁
文件大?。?/td> 0K
描述： BOARD SAR ADC LTC2378-18
軟件下載： QuikEval II System
設計資源： DC1783A Design Files
DC1783A Schematic
標準包裝： 1
系列： QuikEval™
ADC 的數量： 1
位數： 18
采樣率（每秒）： 1M
數據接口： 串行，SPI?
輸入范圍： ±VREF
在以下條件下的電源（標準）： 13.5mW @ 1MSPS
工作溫度： 0°C ~ 70°C
已用 IC / 零件： LTC2378-18
已供物品： 板
相關產品： DC1075A-ND - BOARD COMPANION
DC1216A-B-ND - BOARD EVAL 122.88MHZ CLOCK
LTC2378CDE-16#TRPBF-ND - IC ADC 16BIT LP SAR 1MSPS 16-DFN
LTC2378CDE-16#PBF-ND - IC ADC 16BIT LP SAR 1MSPS 16-DFN
LTC2378IMS-16#TRPBF-ND - IC ADC 16BIT SPI 1MSPS 16MSOP
LTC2378IMS-16#PBF-ND - IC ADC 16BIT SPI 1MSPS 16MSOP
LTC2378IDE-16#TRPBF-ND - IC ADC 16BIT SPI 1MSPS 16DFN
LTC2378IDE-16#PBF-ND - IC ADC 16BIT SPI 1MSPS 16DFN
LTC2378HMS-16#TRPBF-ND - IC ADC 16BIT SPI 1MSPS 16MSOP
LTC2378HMS-16#PBF-ND - IC ADC 16BIT SPI 1MSPS 16MSOP
更多...
LTC2378-18
14
237818f
Figure 11. 32k Point FFT with fIN = 2kHz of the LTC2378-18
FREQUENCY (kHz)
0
100
200
300
500
400
–180
AMPLITUDE
(dBFS)
–60
–40
–20
–80
–100
–120
–140
–160
0
237818 F11
SNR = 102.3dB
THD = –124dB
SINAD = 102.2dB
SFDR = 126dB
APPLICATIONS INFORMATION
0μA to a maximum of 0.75mA at 1Msps. This step in DC
current draw triggers a transient response in the reference
that must be considered since any deviation in the refer-
ence output voltage will affect the accuracy of the output
code. In applications where the transient response of the
reference is important, the fast settling LTC6655-5 refer-
ence is also recommended.
DYNAMIC PERFORMANCE
Fast Fourier Transform (FFT) techniques are used to test
the ADC’s frequency response, distortion and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequen-
cies outside the fundamental. The LTC2378-18 provides
guaranteed tested limits for both AC distortion and noise
measurements.
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
frequency. Figure 11 shows that the LTC2378-18 achieves
a typical SINAD of 102dB at a 1MHz sampling rate with
a 2kHz input.
Signal-to-Noise Ratio (SNR)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 11 shows
that the LTC2378-18 achieves a typical SNR of 102dB at
a 1MHz sampling rate with a 2kHz input.
Total Harmonic Distortion (THD)
Total Harmonic Distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (fSMPL/2).
THD is expressed as:
THD
=20log
V2
2 + V32 + V42 +…+ V
N
2
V1
where V1 is the RMS amplitude of the fundamental fre-
quency and V2 through VN aretheamplitudesofthesecond
through Nth harmonics.
POWER CONSIDERATIONS
The LTC2378-18 provides two power supply pins: the
2.5V power supply (VDD), and the digital input/output
interface power supply (OVDD). The flexible OVDD supply
allows the LTC2378-18 to communicate with any digital
logic operating between 1.8V and 5V, including 2.5V and
3.3V systems.
Power Supply Sequencing
The LTC2378-18 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2378-18
has a power-on-reset (POR) circuit that will reset the
LTC2378-18 at initial power-up or whenever the power
supply voltage drops below 1V. Once the supply voltage
re-enters the nominal supply voltage range, the POR will
reinitialize the ADC. No conversions should be initiated
until 20μs after a POR event to ensure the reinitialization
period has ended. Any conversions initiated before this
time will produce invalid results.
相關PDF資料
PDF描述
GCM30DCWH CONN EDGECARD 60POS DIP .156 SLD
GCM30DCWD CONN EDGECARD 60POS DIP .156 SLD
GBM22DCCT CONN EDGECARD 44POS R/A .156 SLD
FPF2004 IC SWITCH LOAD FULL FUNC SC70-5
GCM25DCCN CONN EDGECARD 50POS R/A .156 SLD
相關代理商/技術參數
參數描述
DC1783A-G 功能描述:BOARD SAR ADC LTC2377-18 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
DC1783A-H 功能描述:BOARD SAR ADC LTC2376-18 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
DC1785A 功能描述:BOARD DEMO LTC2991 RoHS:是 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:QuikEval™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
DC1785A 制造商:Linear Technology 功能描述:EVAL BOARD, LTC2991 TEMP, VOLTAGE, CURRE
DC1786A 功能描述:BOARD DEMO LTC2871 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*