- 您現在的位置：買賣IC網 > PDF目錄16612 > DC1145B (Linear Technology)EVAL BOARD FOR LTC4267 PDF資料下載
參數資料
| 型號： | DC1145B |
| 廠商： | Linear Technology |
| 文件頁數： | 4/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR LTC4267 |
| 設計資源： | DC1145B Design Files |
| 標準包裝： | 1 |
| 主要目的： | 電源管理，以太網供電（POE） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LTC4267 |
| 已供物品： | 板 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4267
12
4267fc
VPORTP
VPORTN
LTC4267
4267 F03
25k SIGNATURE
RESISTOR
SIGNATURE DISABLE
SIGDISA
9k
16k
TO
PSE
Figure 3. 25k Signature Resistor with Disable
Classication
Once the PSE has detected a PD, the PSE may option-
ally classify the PD. Classication provides a method for
more efcient allocation of power by allowing the PSE
to identify lower power PDs and allocate less power for
these devices. The IEEE 802.3af specication denes ve
classes (Table 2) with varying power levels. The designer
selects the appropriate classication based on the power
consumption of the PD. For each class, there is an as-
sociated load current that the PD asserts onto the line
during classication probing. The PSE measures the PD
load current to determine the proper classication and
PD power requirements.
During classication (Figure 4), the PSE presents a xed
voltage between – 15.5V and – 20.5V to the PD. With the
input voltage in this range, the LTC4267 asserts a load
current from the VPORTP pin through the RCLASS resistor.
The magnitude of the load current is set by the RCLASS
resistor. The resistor values associated with each class
are shown in Table 2. Note that the switching regulator
will not interfere with the classication measurement since
the LTC4267 has not passed power to the regulator.
Table 2. Summary of IEEE 802.3af Power Classications and
LTC4267 RCLASS Resistor Selection
Maximum
Nominal
LTC4267
Power Levels
Classication
RCLASS
at Input of PD
Load Current
Resistor
Class
Usage
(W)
(mA)
(Ω, 1%)
0
Default
0.44 to 12.95
<5
Open
1
Optional
0.44 to 3.84
10.5
124
2
Optional
3.84 to 6.49
18.5
68.1
3
Optional
6.49 to 12.95
28
45.3
4
Reserved
Reserved*
40
30.9
*Class 4 is currently reserved and should not be used.
The IEEE 802.3af specication limits the classication
time to 75ms because a signicant amount of power is
dissipated in the PD. The LTC4267 is designed to handle the
power dissipation for this time period. If the PSE probing
exceeds 75ms, the LTC4267 may overheat. In this situation,
the thermal protection circuit will engage and disable the
classication current source in order to protect the part.
The LTC4267 stays in classication mode until the input
voltage rises above the UVLO turn-on voltage.
VPORTN Undervoltage Lockout
The IEEE specication dictates a maximum turn-on voltage
of 42V and a minimum turn-off voltage of 30V for the PD.
In addition, the PD must maintain large on-off hysteresis
to prevent resistive losses in the wiring between the PSE
and the PD from causing start-up oscillation. The LTC4267
incorporates an undervoltage lockout (UVLO) circuit that
monitors the line voltage at VPORTN to determine when
to apply power to the integrated switching regulator
(Figure 5). Before the power is applied to the switching
regulator, the POUT pin is high impedance and sitting at
the ground potential since there is no charge on capacitor
C1. When the input voltage rises above the UVLO turn-on
threshold, the LTC4267 removes the detection and clas-
sication loads and turns on the internal power MOSFET.
C1 charges up under the LTC4267 current limit control
and the POUT pin transitions from 0V to VPORTN. This
sequence is shown in Figure 1. The LTC4267 includes
a hysteretic UVLO circuit on VPORTN that keeps power
applied to the load until the input voltage falls below the
UVLO turn-off threshold. Once the input voltage drops
below –30V, the internal power MOSFET is turned off and
Figure 4. IEEE 802.3af Classication Probing
APPLICATIO S I FOR ATIO
WU
UU
VPORTP
RCLASS
VPORTN
LTC4267
CONSTANT
LOAD
CURRENT
INTERNAL
TO LTC4267
4267 F04
RCLASS
CURRENT PATH
V
PD
PSE
PSE CURRENT MONITOR
PSE
PROBING
VOLTAGE
SOURCE
–15.5V TO –20.5V
相關PDF資料 |
PDF描述 |
|---|---|
| 6-1676941-0 | INDUCTOR 33UH 2.5A SMD |
| RCC17DRYH | CONN EDGECARD 34POS DIP .100 SLD |
| VE-B2W-EW | CONVERTER MOD DC/DC 5.5V 100W |
| HCC10DRTN | CONN EDGECARD 20POS DIP .100 SLD |
| V110C36C100B | CONVERTER MOD DC/DC 36V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1149D17XX-D4X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| DC1149E25XX-D4X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| DC1149E29XX_D4X WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| DC114R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DC115 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。