23 FN6785.0 July 29, 2010 OCFG0, OCFG1 Input Pins These two pins define the configuration of the four output stages. They ar" />
參數資料
型號： D2-45157-QR
廠商： Intersil
文件頁數： 16/31頁
文件大?。?/td> 0K
描述： IC DGTL AMP PWM CTRLR 68QFN
標準包裝： 30
系列： D2Audio™
類型： D 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 30W x 2 @ 8 歐姆
電源電壓： 9 V ~ 26 V
安裝類型： 表面貼裝
供應商設備封裝： 68-QFN 裸露焊盤（10x10）
封裝/外殼： 68-VFQFN 裸露焊盤
包裝： 管件
D2-45057, D2-45157
23
FN6785.0
July 29, 2010
OCFG0, OCFG1 Input Pins
These two pins define the configuration of the four output
stages. They are logic level input pins, and are connected
to logic high (PWMVDD) or logic ground (PWMGND) to
establish which of the four output configurations is used
in the design. Refer to “Pin Description” starting on
page 10 for additional reference and definition.
nERROR/CFG0 and PSSYNC/CFG1 Pins
These pins define the amplifier configuration mode that
the firmware uses in operating the amplifier. In addition
to the OCFG0 and OCFG1 pins that set operation of the
output stages, these nERROR/CFG0 and PSSYNC/CFG1
pins also establish audio signal processing path
assignments and set up monitoring and protection for
are assigned by pull-up or pull-down resistors installed
on that application.
The configuration defined by these pins is assigned when
the D2-45057, D2-45157 device exits its reset state,
when at that time, the logic status of these
PSSYNC/CFG1 and nERROR/CFG0 pins are latched into
internal device registers. These are shared-function pins,
and after firmware begins executing, their functions are
reassigned as outputs. Refer to Table 5 on page 24 for
further description on these pins and their shared
functions.
Temperature Monitoring
The TEMPREF/SCK, TEMP1/MOSI, and TEMPCOM/TIO0
pins are used in a firmware-controlled algorithm to
monitor temperature. These pins share other functions
(refer to multiple-purpose pins descriptions in Table 5 on
page 24) and during firmware execution, operate as
inputs and outputs for this measurement algorithm.
Figure 16 shows the circuit for this temperature
measurement implementation.
A NTC (Negative Temperature Coefficient) 100kΩ resistor
connects to the TEMP1/MOSI pin, and using the resistor’s
temperature/resistance correlation, the firmware
monitors temperature of the NTC resistor. The internal
device timing functions associated with the TIO0 pin
provide calibration that correlates to system clock. A
49.9kΩ resistor connects to the TEMPREF/SCK pin and is
used as a constant non-temperature-dependent
reference for this algorithm.
The firmware algorithm is internal to the D2-45057,
D2-45157 device. Status from this temperature monitor
is used for the temperature protection functions of the
device and its application. There are no adjustments or
parameters for changing settings.
FIGURE 16. TEMPERATURE MONITOR CIRCUIT
100k
49.9k
10
0.1F
TEMP1/MOSI
TEMPREF/SCK
TEMPCOM/TIO0
相關PDF資料
PDF描述
DS1080CLU+ IC CRYSTAL MULTIPLIER SS 8-MSOP
DS1080LU+A00 IC CRYSTAL MULT SS 8-USOP
DS1085LZ-12+ IC ECONOSCILLATOR SYNTH 8-SOIC
DS1085Z-25+ IC ECONOSCILLATOR SYNTH 8-SOIC
DS1086HU-C02+ IC ECONOSCILLATOR SS 8-USOP
相關代理商/技術參數
參數描述
D2-45157-QR-T 功能描述:音頻 DSP DAE-4P MULTI-DIE LW- PWR CLASS-AMPLIFIER RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
D245-5 制造商:KLEIN TOOLS 功能描述:Plier, Diagonal-Cutting; Tapered; 5-1/16 in.; 11/16 in.; 9/16 in.; 3/8 in.; Red 制造商:Klein Tools Inc 功能描述:TOOLS PLIERS 制造商:KLEIN TOOLS 功能描述:TOOLS, PLIERS; Plier Style:Diagonal Cutting; Jaw Length:18mm; Overall Length:129mm; Features:Tapered nose gets in confined areas; ideal for close-tip cutting; Handle Color:Red ;RoHS Compliant: NA 制造商:Klein Tools Inc 功能描述:Standard Diagonal Cutting Pliers
D245-5C 制造商:Klein Tools Inc 功能描述:
D246 制造商:PETERMANN 制造商全稱:PETERMANN 功能描述:HIGH RELIABILITY FOR LOW COST
D24-6 制造商:RICHARD MANNO 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*