- 您現在的位置：買賣IC網 > PDF目錄9003 > CY28409OC (Silicon Laboratories Inc)IC CLOCK CK409GRANTSDALE 56TSSOP PDF資料下載
參數資料
| 型號： | CY28409OC |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK CK409GRANTSDALE 56TSSOP |
| 標準包裝： | 26 |
| 類型： | * |
| PLL： | 是 |
| 輸入： | 晶體 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:21 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 400MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
CY28409
........................Document #: 38-07445 Rev. *D Page 3 of 16
Frequency Select Pins (FS_A, FS_B)
Host clock frequency selection is achieved by applying the
appropriate logic levels to FS_A and FS_B inputs prior to
VTT_PWRGD# assertion (as seen by the clock synthesizer).
Upon VTT_PWRGD# being sampled LOW by the clock chip
(indicating processor VTT voltage is stable), the clock chip
samples the FS_A and FS_B input values. For all logic levels
of FS_A and FS_B except MID, VTT_PWRGD# employs a
one-shot functionality in that once a valid LOW on
VTT_PWRGD#
has
been
sampled
LOW,
all
further
VTT_PWRGD#, FS_A and FS_B transitions will be ignored. In
the case where FS_B is at mid level when VTT_PWRGD# is
sampled LOW, the clock chip will assume “Test Clock Mode.”
Once “Test Clock Mode” has been invoked, all further FS_B
transitions will be ignored and FS_A will asynchronously
select between the Hi-Z and REF/N mode. Exiting test mode
is accomplished by cycling power with FS_B in a HIGH or
LOW state.
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers, can be individually enabled or disabled.
The registers associated with the Serial Data Interface
initializes to their default setting upon power-up, and therefore
use of this interface is optional. Clock device register changes
are normally made upon system initialization, if any are
required. The interface cannot be used during system
operation for power management functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For byte write and byte read operations, the
system controller can access individually indexed bytes. The
offset of the indexed byte is encoded in the command code,
as described in Table 3.
The block write and block read protocol is outlined in Table 4
while Table 5 outlines the corresponding byte write and byte
read protocol. The slave receiver address is 11010010 (D2h).
Table 1. Frequency Select Table (FS_A, FS_B)
FS_A
FS_B
CPU
SRC
3V66
PCIF/PCI
REF0
REF1
USB/DOT
0
100 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
0
MID
REF/N
0
1
200 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
1
0
133 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
1
MID
Hi-Z
Table 2. Frequency Select Table (FS_A, FS_B) SMBus Bit 5 of Byte 6 = 1
FS_A
FS_B
CPU
SRC
3V66
PCIF/PCI
REF0
REF1
USB/DOT
0
200 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
0
1
400 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
1
0
266 MHz
100/200 MHz
66 MHz
33 MHz
14.3 MHz
14.31 MHz
48 MHz
Table 3. Command Code Definition
Bit
Description
7
0 = Block read or block write operation, 1 = Byte read or byte write operation
(6:0)
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be
'0000000'
Table 4. Block Read and Block Write Protocol
Block Write Protocol
Block Read Protocol
Bit
Description
Bit
Description
1
Start
1
Start
2:8
Slave address – 7 bits
2:8
Slave address – 7 bits
9
Write = 0
9
Write = 0
10
Acknowledge from slave
10
Acknowledge from slave
11:18
Command Code – 8 bits
'00000000' stands for block operation
11:18
Command Code – 8 bits
'00000000' stands for block operation
19
Acknowledge from slave
19
Acknowledge from slave
相關PDF資料 |
PDF描述 |
|---|---|
| CY28409AZXC | IC CLOCK CK409GRANTSDALE 56TSSOP |
| VE-B4H-MY-F3 | CONVERTER MOD DC/DC 52V 50W |
| VE-B4H-MY-F2 | CONVERTER MOD DC/DC 52V 50W |
| VE-B4F-MY-F4 | CONVERTER MOD DC/DC 72V 50W |
| VE-B4F-MY-F3 | CONVERTER MOD DC/DC 72V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY28409OCT | 功能描述:時鐘合成器/抖動清除器 SysClk Intel Grntsdl 865 and 875 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28409OCXT | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Clock Synthesizer with Differential SRC and CPU Outputs |
| CY28409OXC | 功能描述:時鐘合成器/抖動清除器 SysClk Intel Grntsdl 865 and 875 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28409OXCT | 功能描述:時鐘合成器/抖動清除器 SysClk Intel Grntsdl 865 and 875 chipsets RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CY28409ZC | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Clock Synthesizer with Differential SRC and CPU Outputs |
發布緊急采購，3分鐘左右您將得到回復。