參數資料
型號: CWR11JB105JCB
廠商: KEMET Corporation
英文描述: SOLID TANTALUM CHIP CAPACITORS
中文描述: 固體鉭芯片電容器
文件頁數: 4/5頁
文件大小: 669K
代理商: CWR11JB105JCB
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Performance Notes
1. Cover Tape Break Force:
1.0 Kg Minimum.
2. Cover Tape Peel Strength:
The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
Peel Strength
8 mm
0.1 Newton to 1.0 Newton (10g to 100g)
12 mm
0.1 Newton to 1.3 Newton (10g to 130g)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier
tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape
shall be pulled at a velocity of 300 ±10 mm/minute.
3. Reel Sizes:
Molded tantalum capacitors are available on either 180 mm (7") reels (standard) or 330 mm (13")
reels (with C-7280). Note that 13
reels are preferred.
4. Labeling:
Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes.
Refer to EIA-556.
Embossed Carrier Tape Configuration:
Figure 1
NOTES
1. B1 dimension is a reference dimension for tape feeder clearance only.
2. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location and hole location shall be applied independent of each other.
3. Tape with components shall pass around radius
R
without damage (see sketch A). The minimum trailer length (Fig. 2) may require
additional length to provide R min. for 12 mm embossed tape for reels with hub diameters approaching N min. (Table 2)
4. The cavity defined by A
,
B
,
and K
shall be configured to surround the part with sufficient clearance such that the chip does not pro-
trude beyond the sealing plane of the cover tape, the chip can be removed from the cavity in a vertical direction without mechanical
restriction, rotation of the chip is limited to 20 degrees maximum in all 3 planes, and lateral movement of the chip is restricted to 0.5 mm
maximum in the pocket (not applicable to vertical clearance.)
Table 1 — EMBOSSED TAPE DIMENSIONS
(Metric will govern)
Constant Dimensions — Millimeters (Inches)
E
P
0
Tape Size
D
0
P
2
T Max
T
1
Max
8 mm
and
12 mm
1.5
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05
0.600
0.100
+0.10 -0.0
(0.059
+0.004, -0.0)
(0.069 ±0.004)
(0.157 ±0.004)
(0.079 ±0.002)
(0.024)
(0.004)
Variable Dimensions — Millimeters (Inches)
D
1
Min.
F
Note 2
1.0
3.5 ±0.05
Tape Size
Pitch
B
1
Max.
Note 1
4.4
P
1
R Min.
Note 3
25.0
T
2
Max
W
A
0
B
0
K
0
Note 4
8 mm
Single
(4 mm)
4.0 ±0.10
2.5
8.0 ±0.30
(0.173)
(0.039)
(0.138 ±0.002)
(0.157 ±0.004) (0.984)
(0.098)
(.315 ±0.012)
12 mm
Double
(8 mm)
8.2
1.5
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10
(0.315 ±0.004) (1.181)
30.0
4.6
12.0 ±0.30
(0.323)
(0.059)
(0.181) (0.472 ±0.012)
TANTALUM, CERAMIC AND
ALUMINUM CHIP CAPACITORS
Packaging Information
94
相關PDF資料
PDF描述
CWR11JB105JCC SOLID TANTALUM CHIP CAPACITORS
CWR11JB105JDA SOLID TANTALUM CHIP CAPACITORS
CWR11JB105JDB SOLID TANTALUM CHIP CAPACITORS
CWR11JB105JDC SOLID TANTALUM CHIP CAPACITORS
CWR11JB105JMA SOLID TANTALUM CHIP CAPACITORS
相關代理商/技術參數
參數描述
CWR11JB105JCC 制造商:AVX Corporation 功能描述:CAP 1UF 20VDC 5% 3.2 X 1.6 X 1.6MM SMD 3216-18 0.01% - Bulk
CWR11JB105KB 制造商:KYOCERA ELCO Corporation 功能描述:Cap Tant Solid 1uF 20V A CASE 10% (3.2 X 1.6 X 1.6mm) SMD 3216-18 (0.1%FR) 10 Ohm 125 制造商:AVX Corporation 功能描述:CAP 1UF 20VDC 10% 3.2 X 1.6 X 1.6MM SMD 3216-18 0.1% - Bulk 制造商:AVX 功能描述:Cap Tant Solid 1uF 20V A CASE 10% (3.2 X 1.6 X 1.6mm) SMD 3216-18 (0.1%FR) 10 Ohm 125
CWR11JB105KBA 制造商:AVX Corporation 功能描述:CAP 1UF 20VDC 10% 3.2 X 1.6 X 1.6MM SMD 3216-18 0.1% - Bulk
CWR11JB105KBB 制造商:AVX Corporation 功能描述:CAP 1UF 20VDC 10% 3.2 X 1.6 X 1.6MM SMD 3216-18 0.1% - Bulk
CWR11JB105KBC 制造商:AVX Corporation 功能描述:CAP 1UF 20VDC 10% 3.2 X 1.6 X 1.6MM SMD 3216-18 0.1% - Bulk