- 您現在的位置：買賣IC網 > PDF目錄369674 > CT2500 (Aeroflex Inc.) CT2500 MIL-STD-1397 Type D & E Low Level Serial Interface Protocol Chip PDF資料下載
參數資料
| 型號： | CT2500 |
| 廠商： | Aeroflex Inc. |
| 英文描述： | CT2500 MIL-STD-1397 Type D & E Low Level Serial Interface Protocol Chip |
| 中文描述： | CT2500的MIL - STD - 1397 D型 |
| 文件頁數： | 4/10頁 |
| 文件大小： | 144K |
| 代理商： | CT2500 |
Aeroflex Circuit Technology
SCDCT2500 REV A 6/12/98 Plainview NY (516) 694-6700
4
RCVCNTRL
O
Received Control Bar
Pulses low upon reception of a Control Frame in both Sink and Source modes.
RCVDTA
O
Received Data/Command Word Bar
Pulses low upon reception of a Data or Command word
ERR1, ERR2
O
Error Bit One and Error Bit Two
ERR1
ERR2
0
0
0
1
1
0
1
1
OVRFLOW
O
Overflow
Error
"1" = Overflow occurred in the Received Data Latch. Data not read in time.
RSTERR
I
Reset Error Flags Bar (Internal Pullup)
A low pulse on this line resets the ERR1, ERR2 and OVRFLOW error flags.
POR
I
Power on Reset Bar
A Master reset. A low pulse on this line resets the internal sequences and error flags.
It does not reset the I/O Data latches.
WIOUT
I
Word Identifier Bit Out
The value on this line is latched during STR2 for the WI bit position in the word to be
transmitted. A "0" indicates a Data word and a "1" indicates a Command/Interrupt
word.
WIIN
O
Word Identifier Bit In
The WI bit of the received word is present on this line during RCVDTA and indicates
whether the word is a Data word or a Command/Interrupt word. The value is latched at
the first RCVDTA for an entire Burst Mode reception.
CMDOUT
I
Command Out
Third bit of the transmitted Control Frame.
DTAOUT
I
Data Out
Second bit of the transmitted Control Frame.
LDCNTRL
I
Load Control Frame Bar
This loads the status of CMDOUT, DTAOUT and BIT4OUT into the Control Frame to
be transmitted. Transmission will commence when the loading is completed. This
applies to both Sink and Source modes.
FIFOEN
I
FIFO Enable
Source Mode
: When FIFOEN is held high ("1"), FIFORD’s (FIFO Read Bars) will be
generated when the input data latch is empty (RDYFORDTA = 1). During the FIFORD,
data presented to the parallel bus will be loaded into the input data latch and
transmitted when ready. In a non-burst (single word) condition, FIFOEN must be
removed before RDYFORDTA comes back. A positive pulse of 100 ns duration
satisfies this requirement.
Sink Mode
: The parallel data bus goes active during RCVDTA and will hold for
approximately 25 ns after its rising edge. With a FIFO directly connected to the data
bus, RCVDTA can be used to load all received words into the FIFO. Gating RCVDTA
with WIIN selects only the data words for loading.
I/O FUNCTION LISTING (Continued)
NAME
I/O
DESCRIPTION
No Error
Bit Count Error in Received Data/Command word or Control Frame
Parity Error in Received Data
Sync Error in Received Data/Command word or Control Frame
相關PDF資料 |
PDF描述 |
|---|---|
| CT2510 | CT2512 / CT2513 / CT2510 / CT2511 Dual Redundant Remote Terminal FOR MIL-STD-1553B |
| CT2510-FP | CT2512 / CT2513 / CT2510 / CT2511 Dual Redundant Remote Terminal FOR MIL-STD-1553B |
| CT2511 | CT2512 / CT2513 / CT2510 / CT2511 Dual Redundant Remote Terminal FOR MIL-STD-1553B |
| CT2511-FP | CT2512 / CT2513 / CT2510 / CT2511 Dual Redundant Remote Terminal FOR MIL-STD-1553B |
| CT2512 | CT2512 / CT2513 / CT2510 / CT2511 Dual Redundant Remote Terminal FOR MIL-STD-1553B |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT-2500 | 功能描述:折皺器 BATT PWR CRIMP TOOL RoHS:否 制造商:Hirose Connector 類型: 描述/功能:Cable and Shield Crimper |
| CT-2500/5 | 制造商:American Technical Ceramics Corp 功能描述:Current Transformers 制造商:ATC 功能描述:Current Transformers |
| CT2500-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Protocol Controller |
| CT-2500BC | 功能描述:手工工具 Rechargeable Tool Battery, for use with RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
| CT-2500CASE | 功能描述:手工工具 Carrying Case, holds CT-2500 and accesso RoHS:否 制造商:Molex 產品:Extraction Tools 類型: 描述/功能:Extraction tool |
發布緊急采購，3分鐘左右您將得到回復。