- 您現在的位置：買賣IC網 > PDF目錄4077 > CP80C88-2Z (Intersil)IC PWM CONTROLLER PDF資料下載
參數資料
| 型號： | CP80C88-2Z |
| 廠商： | Intersil |
| 文件頁數： | 34/38頁 |
| 文件大小： | 0K |
| 描述： | IC PWM CONTROLLER |
| 標準包裝： | 99 |
| 處理器類型： | 80C88 8/16-位 |
| 速度： | 8MHz |
| 電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 40-DIP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁
5
FN2949.4
February 22, 2008
Pin Description
The following pin function descriptions are for 80C88 system in minimum mode (i.e., MN/MX = VCC). Only the pin functions which
are unique to the minimum mode are described; all other pin functions are as described above.
SYMBOL
PIN
NUMBER
TYPE
DESCRIPTION
MINIMUM MODE SYSTEM (i.e., MN/MX = VCC)
IO/M
28
O
STATUS LINE: is an inverted maximum mode S2. It is used to distinguish a memory access from an I/O
access. IO/M becomes valid in the T4 preceding a bus cycle and remains valid until the final T4 of the cycle
(I/O = HIGH, M = LOW). IO/M is held to a high impedance logic one during local bus “hold acknowledge”.
WR
29
O
Write: strobe indicates that the processor is performing a write memory or write I/O cycle, depending on
the state of the IO/M signal. WR is active for T2, T3, and Tw of any write cycle. It is active LOW, and is held
to high impedance logic one during local bus “hold acknowledge”.
INTA
24
O
INTA: is used as a read strobe for interrupt acknowledge cycles. It is active LOW during T2, T3 and Tw of
each interrupt acknowledge cycle. Note that INTA is never floated.
ALE
25
O
ADDRESS LATCH ENABLE: is provided by the processor to latch the address into the 82C82/82C83
address latch. It is a HIGH pulse active during clock low of T1 of any bus cycle. Note that ALE is never
floated.
DT/R
27
O
DATA TRANSMIT/RECEIVE: is needed in a minimum system that desires to use an 82C86/82C87 data
bus transceiver. It is used to control the direction of data flow through the transceiver. Logically, DT/R is
equivalent to S1 in the maximum mode, and its timing is the same as for IO/M (T = HIGH, R = LOW). This
signal is held to a high impedance logic one during local bus “hold acknowledge”.
DEN
26
O
DATA ENABLE: is provided as an output enable for the 82C86/82C87 in a minimum system which uses
the transceiver. DEN is active LOW during each memory and I/O access, and for INTA cycles. For a read
or INTA cycle, it is active from the middle of T2 until the middle of T4, while for a write cycle, it is active from
the beginning of T2 until the middle of T4. DEN is held to high impedance logic one during local bus “hold
acknowledge”.
HOLD,
HLDA
31
30
I
O
HOLD: indicates that another master is requesting a local bus “hold”. To be acknowledged, HOLD must be
active HIGH. The processor receiving the “hold” request will issue HLDA (HIGH) as an acknowledgment,
in the middle of a T4 or T1 clock cycle. Simultaneous with the issuance of HLDA the processor will float the
local bus and control lines. After HOLD is detected as being LOW, the processor lowers HLDA, and when
the processor needs to run another cycle, it will again drive the local bus and control lines.
Hold is not an asynchronous input. External synchronization should be provided if the system cannot
otherwise guarantee the set up time.
SS0
34
O
STATUS LINE: is logically equivalent to S0 in
the maximum mode. The combination of SS0,
IO/M and DT/R allows the system to completely
decode the current bus cycle status. SS0 is held
to high impedance logic one during local bus
“hold acknowledge”.
IO/M
DT/R
SS0
CHARACTERISTICS
1
0
Interrupt Acknowledge
1
0
1
Read I/O Port
1
0
Write I/O Port
11
1
Halt
0
Code Access
0
1
Read Memory
0
1
0
Write Memory
01
1
Passive
80C88
相關PDF資料 |
PDF描述 |
|---|---|
| AYF331335 | CONN FPC 13POS .3MM SMD |
| MPC8314ECVRAFDA | MPU POWERQUICC II PRO 620-PBGA |
| MPC8313ZQAFFB | MPU POWERQUICC II PRO 516-PBGA |
| MPC8313CZQADDB | MPU POWERQUICC II PRO 516-PBGA |
| MPC8315ECVRADDA | MPU POWERQUICC II PRO 620-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP80C88R2489 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP80C88Z | 功能描述:IC PWM CONTROLLER RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:40 系列:MPC83xx 處理器類型:32-位 MPC83xx PowerQUICC II Pro 特點:- 速度:267MHz 電壓:0.95 V ~ 1.05 V 安裝類型:表面貼裝 封裝/外殼:516-BBGA 裸露焊盤 供應商設備封裝:516-PBGAPGE（27x27） 包裝:托盤 |
| CP80S53 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM/ROM-Based 8-Bit Microcontroller Series CP80S53A可替代PIC12C508/509 |
| CP80S53A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM/ROM-Based 8-Bit Microcontroller Series CP80S53A可替代PIC12C508/509 |
| CP80S54 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM/ROM-Based 8-Bit Microcontroller Series |
發布緊急采購，3分鐘左右您將得到回復。