- 您現在的位置：買賣IC網 > PDF目錄11796 > CP2103-GM (Silicon Laboratories Inc)IC CTRLR BRIDGE USB-UART 28QFN PDF資料下載
參數資料
| 型號： | CP2103-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR BRIDGE USB-UART 28QFN |
| 產品培訓模塊： | USB Protocol Products USBXpress CP21xx USB Bridge |
| 標準包裝： | 73 |
| 應用： | USB |
| 接口： | USB |
| 電源電壓： | 3 V ~ 3.6 V |
| 封裝/外殼： | 28-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 28-QFN（5x5） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 627 (CN2011-ZH PDF) |
| 配用： | 336-1163-ND - KIT EVAL FOR CP2103 USB TO UART |
| 其它名稱： | 336-1164 |
CP2103
8
Rev. 1.0
3. Pinout and Package Definitions
Table 7. CP2103 Pin Definitions
Name
Pin #
Type
Description
VDD
6
Power In
Power Out
3.0–3.6 V Power Supply Voltage Input.
3.3 V Voltage Regulator Output. See "9. Voltage Regulator" on page
16.
VIO
5
Power In
1.8 V to VDD I/O Supply Voltage Input.
GND
2
Ground. Must be tied to ground.
SGND
Ground. Must be tied to ground.
RST
9
D I/O
Device Reset. Open-drain output of internal POR or VDD monitor. An
external source can initiate a system reset by driving this pin low for
at least 15 s.
REGIN
7
Power In
5 V Regulator Input. This pin is the input to the on-chip voltage regu-
lator.
VBUS
8
D In
VBUS Sense Input. This pin should be connected to the VBUS signal
of a USB network. A 5 V signal on this pin indicates a USB network
connection.
D+
3
D I/O
USB D+
D–
4
D I/O
USB D–
TXD
25
D Out
Asynchronous data output (UART Transmit)
RXD
24
D In
Asynchronous data input (UART Receive)
CTS
22*
D In
Clear To Send control input (active low)
RTS
23*
D Out
Ready to Send control output (active low)
DSR
26*
D in
Data Set Ready control input (active low)
DTR
27*
D Out
Data Terminal Ready control output (active low)
DCD
28*
D In
Data Carrier Detect control input (active low)
RI
1*
D In
Ring Indicator control input (active low)
SUSPEND
12*
D Out
This pin is driven high when the CP2103 enters the USB suspend
state.
SUSPEND
11*
D Out
This pin is driven low when the CP2103 enters the USB suspend
state.
NC
10, 13–15,
20–21
These pins should be left unconnected or tied to VDD.
GPIO.3
16
D I/O
User-configurable input or output.
GPIO.2
17
D I/O
User-configurable input or output.
GPIO.1
18
D I/O
User-configurable input or output.
GPIO.0
19
D I/O
User-configurable input or output.
*Note: Pins can be left unconnected when not used.
相關PDF資料 |
PDF描述 |
|---|---|
| CP2101-GM | IC CTRLR BRIDGE USB-UART 28MLP |
| 1604059-2 | KIT,350A,2/0 AWG,ORANGE |
| 1604059-1 | KIT,350A,2/0 AWG,YELLOW |
| 1604045-4 | KIT,175A,1 AWG,GRAY |
| MS3106F20-22S | CONN PLUG 6POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2103-GMR | 功能描述:輸入/輸出控制器接口集成電路 USB-TO-UART BRIDGE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2104 | 制造商:SILABS 制造商全稱:SILABS 功能描述:USB DRIVER CUSTOMIZATION |
| CP2104EK | 功能描述:界面開發工具 Evaluation kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CP2104-F03-GM | 功能描述:輸入/輸出控制器接口集成電路 USB to UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2104-F03-GMR | 功能描述:輸入/輸出控制器接口集成電路 USB to UART bridge RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。