參數資料
型號: CAT37TDI-TE7
元件分類: LED驅動器
英文描述: CMOS White LED Driver Boost Converter
中文描述: 的CMOS白光LED驅動器升壓轉換器
文件頁數: 8/12頁
文件大?。?/td> 566K
代理商: CAT37TDI-TE7
CAT37
8
Doc. No. 5005, Rev. S
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
PCB LAYOUT GUIDELINES
The CAT37 is a high-frequency switching regulator
where proper PCB board layout and component
placement can minimize noise and radiation and increase
efficiency. To maximize efficiency, the CAT37 design
has fast switch rise and fall times. To prevent radiation
and high frequency resonance problems minimize the
length and area of all traces connected to the SW pin and
use a ground plane under the switching regulator.
The SW pin, schottky diode and capacitor C2 signal
path should be kept as short as possible. The ground
connection for the R1
resistor should be tied directly to
the GND pin and not be shared with other components.
LED DIMMING WITH DC SIGNAL
Dimming the LEDs can be done by applying a variable
DC voltage as shown on Figure 3. As the V
DC
increase
the voltage across R1 decreases and therefore lower
the LED current. The resistors R2 and R3 must be large
enough so that their current (tens of
μ
A) is much smaller
than the LED current but much larger than the FB
leakage current (I
FB
). When adjusting V
DC
between 0V
and 2V, the resistors shown on Figure 3 will set the LED
current between 0mA and 15mA.
LED DIMMING WITH PWM SIGNAL
PWM brightness control provides the widest dimming
range (greater than 20:1). By turning the LEDs ON and
OFF using the control signal, the LEDs operate at either
zero or full current, but their average current changes
with the PWM signal duty cycle. Typically, a 5kHz to
40kHz PWM signal is used.
A filtered PWM signal is used to dim the LEDs, as shown
in Figure 4.
In addition to providing the widest dimming range, PWM
brightness control also ensures the
purest
white LED
color over the entire dimming range. The true color of a
white LED changes with operating current, and is the
purest
white at a specific forward current, usually
15mA or 20mA. If the LED current is less than or more
than this value, the emitted light becomes more blue.
Applications involving color LCDs can find the blue tint
objectionable.
Figure 3. Dimming with a
DC Voltage
CAT37
FB
R1
RINCR
LOGIC
SIGNAL
2N7002
CAT37
FB
R3
18k
PWM
10k
R2
1k
CAT37
FB
R3
18k
VDC
R2
1k
Figure 4. Dimming with a Filtered
PWM Signal
Figure 5. Dimming with a
Logic Signal
LED DIMMING WITH A LOGIC SIGNAL
For applications that need to adjust the LED brightness
in discrete steps, a logic signal can be used as shown in
Figure 5. R
1
sets the minimum LED current value (when
the NMOS switch is OFF):
R1=0.095V
I
LED(MIN)
R
determines how much LED current increases
when the external NMOS switch is turned ON.
R
INCR
=
0.095V
I
LED(INCREASE)
相關PDF資料
PDF描述
CAT4004 4-Channel Constant Current LED Driver with EZDi TM
CAT4004VP2-T3 4-Channel Constant Current LED Driver with EZDi TM
CAT4238 High Efficiency 10 LED Boost Converter
CAT4238TD-GT3 High Efficiency 10 LED Boost Converter
CAT5241WI-10 Quad Digitally Programmable Potentiometers (DPP⑩) with 64 Taps and 2-wire Interface
相關代理商/技術參數
參數描述
CAT-38-PP 功能描述:INSTALL TOOL ORANGE FOR SHR SER RoHS:是 類別:工具 >> 螺線形繞線,伸縮套管 系列:- 標準包裝:1 系列:Slit-N-Wrap®
CAT-38-PP-BU 功能描述:INSTALL TOOL ORANGE FOR SHR SER RoHS:是 類別:工具 >> 螺線形繞線,伸縮套管 系列:- 標準包裝:1 系列:Slit-N-Wrap®
CAT4002A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Constant Current LED Driver with 32 Dimming Levels and Rset
CAT4002A_10 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Constant Current LED Driver with 32 Dimming Levels and Rset
CAT4002ASD-GT3 功能描述:LED照明驅動器 LED DR 2 CH EZ DIM I/F RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N