- 您現在的位置：買賣IC網 > PDF目錄369655 > CAT3636HV32 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 PDF資料下載
參數資料
| 型號： | CAT3636HV32 |
| 英文描述： | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| 中文描述： | 6聲道四ModeTM分數的LED驅動器在TQFN3x3 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 434K |
| 代理商： | CAT3636HV32 |
CAT3636
2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. 5020 Rev. A
PIN DESCRIPTION
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13/14
15
16
TAB
Name
LEDC2
LEDC1
LEDB2
LEDB1
LEDA2
LEDA1
VOUT
VIN
C1+
C1-
C2+
C2-
NC
GND
EN/SET
TAB
Function
LEDC2 cathode terminal
LEDC1 cathode terminal
LEDB2 cathode terminal
LEDB1 cathode terminal
LEDA2 cathode terminal
LEDA1 cathode terminal
Charge pump output, connect to LED anodes
Charge pump input, connect to battery or supply
Bucket capacitor 1, positive terminal
Bucket capacitor 1, negative terminal
Bucket capacitor 2, positive terminal
Bucket capacitor 2, negative terminal
No connect
Ground reference
Device enable (active high) and 1 wire control input
Connect to GND on the PCB
PIN FUNCTION
VIN
is the supply pin for the charge pump. A small
1
μ
F ceramic bypass capacitor is required between the
VIN pin and ground near the device. The operating
input voltage range is from 2.5V to 5.5V. Whenever
the input supply falls below the under-voltage
threshold (2V) all the LED channels will be
automatically disabled and the device register are
reset to default values.
EN/SET
is the enable and one wire addressable
control logic input for all LED channels. Guaranteed
levels of logic high and logic low are set at 1.3V and
0.4V respectively. When EN/SET is initially taken
high, the device becomes enabled and all LED
currents remain at 0mA. To place the device into zero
current mode, the EN/SET pin must be held low for
more than 1.5ms.
VOUT
is the charge pump output that is connected to
the LED anodes. A small 1
μ
F ceramic bypass
capacitor is required between the VOUT pin and
ground near the device.
GND
is the ground reference for the charge pump.
The pin must be connected to the ground plane on the
PCB.
C1+, C1-
are connected to each side of the ceramic
bucket capacitor C1.
C2+, C2-
are connected to each side of the
ceramic bucket capacitor C2.
LEDxx
provide the internal regulated current for
each of the LED cathodes. These pins enter high-
impedance zero current state whenever the device
is placed in shutdown mode.
TAB
is the exposed pad underneath the package.
For best thermal performance, the tab should be
soldered to the PCB and connected to the ground
plane.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT3636HV3T | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| CAT37TDI-TE7 | CMOS White LED Driver Boost Converter |
| CAT4004 | 4-Channel Constant Current LED Driver with EZDi TM |
| CAT4004VP2-T3 | 4-Channel Constant Current LED Driver with EZDi TM |
| CAT4238 | High Efficiency 10 LED Boost Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT3636HV3-GT2 | 功能描述:LED照明驅動器 LED Driver,Quad mode,6 ch RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3636HV3T | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| CAT3636HV3-T2 | 功能描述:LED照明驅動器 6-Channel Quad-Mode RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3637 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:6-Channel Programmable High Efficiency Quad-Mode⑩ LED Driver |
| CAT3637AEVB | 功能描述:電源管理IC開發工具 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。