- 您現在的位置：買賣IC網 > PDF目錄369655 > CAT3636HV3-T2 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 PDF資料下載
參數資料
| 型號： | CAT3636HV3-T2 |
| 英文描述： | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| 中文描述： | 6聲道四ModeTM分?jǐn)?shù)的LED驅動器在TQFN3x3 |
| 文件頁數： | 9/16頁 |
| 文件大小： | 404K |
| 代理商： | CAT3636HV3-T2 |
CAT3636
2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. 5020 Rev. C
LED Current Setting
The current in each of the six LED channels is
programmed through the 1-wire EN/SET digital control
input. By pulsing this signal according to a specific
protocol, a set of internal registers can be addressed
and written into allowing to configure each bank of
LEDs with the desired current. There are six registers:
the first five are 4 bits long and the sixth is 1 bit long.
The registers are programmed by first selecting the
register address and then programming data into that
register.
An internal counter records the number of falling
edges to identify the address and data. The address is
serially programmed adhering to low and high
duration time delays. One down pulse corresponds to
register 1 being selected. Two down pulses
correspond to register 2 being selected and so on up
to register 6. T
LO
and T
HI
must be within 200ns to
100
μ
s. Anything below 200ns may be ignored.
Once the final rising edge of the address pointer is
programmed, the user must wait 500
μ
s to 1000
μ
s
before programming the first data pulse falling edge. If
the falling edge of the data is not received within
1000
μ
s, the device will revert back to waiting for an
address.
Data in a register is reset once it is selected by the
address pointer. If a register is selected but no data is
programmed, then the register value is reset back to
its initial default value with all data bits to 0.
Once the final rising edge of the data pulses is
programmed, the user must wait 1.5ms before
programming another address. If programming fails or
is interrupted, the user must wait T
RESETDELAY
2ms from
the last rising edge before reprogramming can
commence.
Upon power-up, the device automatically starts
looking for an address. The device requires a
minimum 10
μ
s delay (T
SETUP
) to ensure the
initialization of the internal logic at power-up. After this
time delay, the device registers may be programmed
adhering to the timing constraints shown in Figure 1. If
no falling edge is detected within 100
μ
s of power-up,
then the user must wait 2ms before trying to program
the device again.
To power-down the device and turn-off all current
sources, the EN/SET input should be kept low for a
duration T
OFF
of 1.5ms or more. The driver typically
powers-down with a delay of about 1ms. All register
data are lost.
Figure 3. EN/SET One Wire Addressable Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| CAT3636 | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| CAT3636HV32 | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| CAT3636HV3T | 6-Channel Quad-ModeTM Fractional LED Driver in TQFN3x3 |
| CAT37TDI-TE7 | CMOS White LED Driver Boost Converter |
| CAT4004 | 4-Channel Constant Current LED Driver with EZDi TM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT3637 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:6-Channel Programmable High Efficiency Quad-Mode⑩ LED Driver |
| CAT3637AEVB | 功能描述:電源管理IC開發工具 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| CAT3637HV3-GT2 | 功能描述:LED照明驅動器 Hi Eff Quad Mode LED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3643 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:3-Channel Ultra High Efficiency Quad-Mode LED Driver |
| CAT3643_0710 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:3-Channel Ultra High Efficiency Quad-Mode⑩ LED Driver |
發布緊急采購，3分鐘左右您將得到回復。