- 您現在的位置：買賣IC網 > PDF目錄369655 > CAT3603HV22 3-Channel LED Driver in 3x3mm Package PDF資料下載
參數資料
| 型號： | CAT3603HV22 |
| 英文描述： | 3-Channel LED Driver in 3x3mm Package |
| 中文描述： | 3通道LED驅動器采用3x3mm封裝 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 510K |
| 代理商： | CAT3603HV22 |
CAT3603
2006 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
9
Doc. No. 5017 Rev. C
LED CURRENT SETTING
The LED current is set by the external resistor R
SET
connected between the RSET pin and ground. Table
1 lists various LED currents and the associated R
SET
resistor value for standard 1% precision surface
mount resistors.
Table 1. RSET Resistor Selection
LED Current (mA)
1
5
10
15
20
25
30
R
SET
(k
)
649
287
102
49.9
32.4
23.7
15.4
The unused LED channels must be disabled by
connecting the respective LED pins to VOUT. A
disabled channel sinks only 0.2mA typical. When the
following equation is true on any channel, the driver
turns off the LED channel:
VOUT - V
LED
≤
1V (LED channel OFF)
Note: The CAT3603 is designed to drive LEDs with forward
voltage greater than 1V and is not compatible with resistive
loads less than 5k
.
External Components
The driver requires a total of four external 1μF ceramic
capacitors: two for decoupling input and output, and
two for the charge pump. Both capacitor types X5R and
X7R are recommended for the LED driver application.
In the 1.5x charge pump mode, the input current ripple
is kept very low by design, and an input bypass
capacitor of 1μF is sufficient. In 1x mode, the device
operating in linear mode does not introduce switching
noise back onto the supply.
Recommended Layout
In 1.5x charge pump mode, the driver switches
internally at a high frequency of 1MHz. It is
recommended to minimize trace length to all four
capacitors. A ground plane should cover the area
under the driver IC as well as the bypass capacitors.
Short connection to ground on capacitors CIN and
COUT can be implemented with the use of multiple
via. A copper area matching the TDFN exposed pad
(GND) must be connected to the ground plane
underneath. The use of multiple via improves the
package heat dissipation.
Figure 3. Recommended Layout
相關PDF資料 |
PDF描述 |
|---|---|
| CAT3603HV2T | 3-Channel LED Driver in 3x3mm Package |
| CAT3604HV4-TE13 | 4-Channel Regulated Charge Pump White LED Driver |
| CAT3604HS4-TE13 | 4-Channel Regulated Charge Pump White LED Driver |
| CAT3604 | 4-Channel Regulated Charge Pump White LED Driver |
| CAT3606HS4 | 6-Channel Low Noise Charge Pump White LED Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT3603HV2T | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:3-Channel LED Driver in 3x3mm Package |
| CAT3603HV2-T2 | 功能描述:LED照明驅動器 3-Channel White LED RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3604 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4-Channel Regulated Charge Pump White LED Driver |
| CAT3604_08 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4-Channel Regulated Charge Pump White LED Driver |
| CAT3604A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:4-Channel Regulated Charge Pump White LED Driver |
發布緊急采購，3分鐘左右您將得到回復。