參數資料
型號： C8051F303-GM
廠商： Silicon Laboratories Inc
文件頁數： 133/178頁
文件大小： 0K
描述： IC 8051 MCU 8K FLASH 11QFN
產品培訓模塊： Serial Communication Overview
標準包裝： 122
系列： C8051F30x
核心處理器： 8051
芯體尺寸： 8-位
速度： 25MHz
連通性： SMBus（2 線/I²C），UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 8
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 10-VFDFN 裸露焊盤
包裝： 管件
產品目錄頁面： 623 (CN2011-ZH PDF)
配用： 336-1444-ND - ADAPTER PROGRAM TOOLSTICK F300
其它名稱： 336-1249
C8051F300/1/2/3/4/5
58
Rev. 2.9
Performance
The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the stan-
dard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system
clock cycles to execute, and usually have a maximum system clock of 12 MHz. By contrast, the CIP-51
core executes 70% of its instructions in one or two system clock cycles, with no instructions taking more
than eight system clock cycles.
With the CIP-51's maximum system clock at 25 MHz, it has a peak throughput of 25 MIPS. The CIP-51 has
a total of 109 instructions. The table below shows the total number of instructions that require each execu-
tion time.
Clocks to Execute
1
2
2/3
3
3/4
4
4/5
5
8
Number of Instructions
26
50
5
14
7
3
1
2
1
Programming and Debugging Support
In-system programming of the Flash program memory and communication with on-chip debug support
logic is accomplished via the Silicon Labs 2-Wire Development Interface (C2). Note that the re-program-
mable Flash can also be read and changed a single byte at a time by the application software using the
MOVC and MOVX instructions. This feature allows program memory to be used for non-volatile data stor-
age as well as updating program code under software control.
The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints, starting, stopping and single stepping through program execution (including interrupt service
routines), examination of the program's call stack, and reading/writing the contents of registers and mem-
ory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or
other on-chip resources. C2 details can be found in Section “17. C2 Interface” on page 173.
The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs pro-
vides an integrated development environment (IDE) including editor, macro assembler, debugger and pro-
grammer. The IDE's debugger and programmer interface to the CIP-51 via the C2 interface to provide fast
and efficient in-system device programming and debugging. Third party macro assemblers and C compil-
ers are also available.
8.1.
Instruction Set
The instruction set of the CIP-51 System Controller is fully compatible with the standard MCS-51 instruc-
tion set. Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51
instructions are the binary and functional equivalent of their MCS-51 counterparts, including opcodes,
addressing modes and effect on PSW flags. However, instruction timing is different than that of the stan-
dard 8051.
8.1.1. Instruction and CPU Timing
In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with
machine cycles varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based
solely on clock cycle timing. All instruction timings are specified in terms of clock cycles.
Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock
cycles as there are program bytes in the instruction. Conditional branch instructions take one less clock
cycle to complete when the branch is not taken as opposed to when the branch is taken. Table 8.1 is the
相關PDF資料
PDF描述
AT32UC3C2512C-Z2ZT IC MCU 32BIT 512KB FLASH 64QFN
AU-Y1005-R CONN USB RTANG FMALE TYPE A PCB
USB-B1HSB6 CONN USB TYPE B R/A BLACK
AT32UC3A0256AU-ALUT IC MCU 256K FLASH 144LQFP
AT32UC3C0256C-ALUT IC MCU AVR32 256K FLASH 144LQFP
相關代理商/技術參數
參數描述
C8051F303-GMR 功能描述:8位微控制器 -MCU 8KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F303-GS 功能描述:8位微控制器 -MCU 8KB Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F303-GSR 功能描述:8位微控制器 -MCU 8KB 14Pin MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F303R 功能描述:8位微控制器 -MCU No ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F304 功能描述:8位微控制器 -MCU 4KB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*