參數資料
型號： AX88190P
廠商： ASIX Electronics Corporation
英文描述： 10/100BASE PCMCIA Fast Ethernet MAC Controller
中文描述： 一個10/100Base的PCMCIA快速以太網MAC控制器
文件頁數： 16/41頁
文件大小： 465K
代理商： AX88190P
AX88190 PCMCIA Fast Ethernet MAC Controller
ASIX ELECTRONICS CORPORATION
16
4.2 PCMCIA Function Configuration Register Set of MODEM
REGISTER
MCOR
MCSR
MIOBASE0
MIOBASE1
NAME
OFFSET
3E0H
3E2H
3EAH
3ECH
CONFIGURATION OPTION REGISTER
CONFIGURATION AND STATUS REGISTER
I/O BASED REGISTER 0
I/O BASED REGISTER 1
Tab - 13 PCMCIA Function Configuration Register Mapping of MODEM
4.2.1 Configuration Option Register of MODEM (MCOR) Offset 3E0H (Read/Write)
FIELD
7
R/W/C
R/W
DESCRIPTION
Software Reset
Assert this bit will reset the MODEM function of AX88190. Return a 0 to this bit will
leave the MODEM function of AX88190 in a post-reset state as same as that following a
hardware reset. The value of this bit is 0 at power-on.
Level IRQ
This bit should be set to 1, the AX88190 always generates Level Mode Interrupt.
Function Configuration Index
These six bits are used to indicate entry of the card configuration table locate in the CIS.
The default value is 0
.
On multifunction PC Card,
Bit 5, Bit4 : Reserved
Bit 3 : IREQ# route to STSCHG#
If bit 0 of MCOR is set to 0, this bit is ignored.
If both bit 0 and bit 2 of MCOR are set to 1 and this bit is set to 1, the MODEM will route
interrupt request to STSCHG# signal. If this bit is set to 0, the MODEM will generate
interrupt request via IREQ# line.
Bit 2 : Enable IREQ# Routing
If bit 0 of MCOR is set to 0, this bit is ignored.
If bit 0 of MCOR is set to 1 and this bit is set to 1, the MODEM will generate interrupt
request via IREQ# signal. If this bit is set to 0, the MODEM will not generate interrupt
request via IREQ# line.
Bit 1 : Enable Base and Limit Registers
If bit 0 of MCOR is set to 0, this bit is ignored.
If bit 0 of MCOR is set to 1 and this bit is set to 1,only I/O addresses that are qualified
by the Base and Limit registers are passed to MODEM function. If this bit is set to 0,all
I/O addresses are passed to LAN function.
Bit 0 : Enable Function
If this bit is set to 0, the MODEM function is disabled.
If this bit is set to 1, the MODEM function is enabled.
6
R/W
5:0
R/W
相關PDF資料
PDF描述
AX88195P 10/100BASE Local CPU Bus Fast Ethernet MAC Controller
AX88196BLF Low-pin-count Non-PCI 8/16-bit 10/100M Fast Ethernet Controller with MII Interface
AX88658AB 8-Port 10/100/1000BASE-T Ethernet Switch
AX88772_07 USB to 10/100 Fast Ethernet/HomePNA Controller
AX88772 USB to 10/100 Fast Ethernet/HomePNA Controller
相關代理商/技術參數
參數描述
AX88195P 制造商:ASIX 制造商全稱:ASIX 功能描述:10/100BASE Local CPU Bus Fast Ethernet MAC Controller
AX88196 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE 3-in-1 Local CPU Bus Fast Ethernet Controller with Embedded SRAM
AX88196BLF 制造商:ASIX 制造商全稱:ASIX 功能描述:Low-pin-count Non-PCI 8/16-bit 10/100M Fast Ethernet Controller with MII Interface
AX88196L 制造商:未知廠家 制造商全稱:未知廠家 功能描述:10/100BASE 3-in-1 Local CPU Bus Fast Ethernet Controller with Embedded SRAM
AX88613 制造商:ASIX 制造商全稱:ASIX 功能描述:ASIX Multi-Port Ethernet Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*