- 您現在的位置：買賣IC網 > Datasheet目錄60 > ATS685LSHTN-T (Allegro Microsystems Inc)IC HALL EFFECT GEAR SENSOR 4SIP Datasheet資料下載
參數資料
| 型號： | ATS685LSHTN-T |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 12/15頁 |
| 文件大小： | 437K |
| 描述： | IC HALL EFFECT GEAR SENSOR 4SIP |
| 特色產品： | ATS685 Sensor IC |
| 標準包裝： | 1 |
| 傳感范圍： | 5mT ~ 150mT |
| 類型： | 專用型 |
| 電源電壓： | 4 V ~ 24 V |
| 電流 - 電源： | 8mA |
| 輸出類型： | 數字式，開漏極 |
| 特點： | 輪齒類型 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 標準包裝 |
| 其它名稱： | 620-1399-6 |
Two-Wire, Zero Speed
Differential Gear Tooth Sensor IC
ATS685LSH
12
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Undervoltage Lockout
When the supply voltage falls below the minimum operating
voltage, V
CC(UV)
, I
CC
goes high and remains high regardless of
the state of the magnetic gradient from the target. This lockout
feature prevents false signals, caused by undervoltage conditions,
from propagating to the output of the device. Because V
CC
is
below the V
CC
(min) specification during lockout, the I
CC
levels
may not be within specification.
Power Supply Protection
The device contains an on-chip regulator and can operate over a
wide V
CC
range. For devices that need to operate from an unregu-
lated power supply, transient protection must be added externally.
For applications using a regulated line, EMI/RFI protection may
still be required. Contact Allegro for information on the circuitry
needed for compliance with various EMC specifications. Refer to
figure 8 for an example of a basic application circuit.
Automatic Gain Control (AGC)
This feature allows the device to operate with an optimal internal
electrical signal, regardless of the air gap (within the AG specifica-
tion). At power-on, the device determines the peak-to-peak ampli-
tude of the signal generated by the target. The gain is then auto-
matically adjusted. Figure 9 illustrates the effect of this feature.
Running Mode Gain Adjust
The ATS685 has a feature during Running mode to compensate
for dynamic air gap variation. If the system increases the mag-
netic input drastically, the device will gradually readjust the gain
downwards, allowing the chip to regain the optimum internal
electrical signal with the new, larger, magnetic signal.
Dynamic Offset Cancellation (DOC)
The offset circuitry when combined with AGC automatically
reduces the effects of chip, magnet, and installation offsets. This
circuitry is continuously active, including both Power-on mode
and Running mode, compensating for any offset drift (within
Allowable User-Induced Differential Offset). Continuous opera-
tion also allows it to compensate for offsets induced by tempera-
ture variations over time.
Running Mode Lockout
The ATS685 has a Running mode lockout feature to prevent
switching on small signals that are characteristic of vibration
signals. The internal logic of the chip evaluates small signal
amplitudes below a certain level to be vibration. In that event, the
output is blanked (locked-out) until the amplitude of the signal
returns to normal operating levels.
Watchdog
The ATS685 employs a watchdog circuit to prevent extended loss
of output switching during sudden impulses and vibration in the
system. If the system changes the magnetic input drastically such
that target feature detection is terminated, the device will fully
reset itself, allowing the chip to recalibrate properly on the new
magnetic input signal.
Mechanical Profile
AG
Small
AG
Large
AG
Small
AG
Large
Internal Differential
Analog Signal
Response, with AGC
Internal Differential
Analog Signal
Response, without AGC
Ferrous Target
V+
V+
Figure 9. Automatic Gain Control (AGC). The AGC function corrects for
variances in the air gap. Differences in the air gap cause differences in
the magnetic field at the device, but AGC prevents that from affecting
device performance, as shown in the lowest panel.
Figure 8. Typical circuit for proper device operation.
2
ATS685
1
3
4
0.01 F (optional)
100
R
SENSE
C
LOAD
C
BYPASS
V
CC
相關PDF資料 |
PDF描述 |
|---|---|
| BU52001GUL-E2 | IC HALL EFFECT SW BIPO VCSP50L1 |
| BU52003GUL-E2 | IC HALL EFFECT SW BIPO VCSP50L1 |
| BU52014HFV-TR | IC HALL EFFECT SW BIPO HVSOF5 |
| BU52040HFV-TR | IC HALL EFFECT BIPO LATCH HVSOF5 |
| D6B-2P | SENSR TILT 35-65DEG 1MA SMD GUL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS692LSHTN-RSNPH-T | 功能描述:IC HALL EFFECT SENSOR 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:專用型 技術:霍爾效應 極化:- 感應范圍:69% 跳閘，31% 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:4 V ~ 24 V 電流 - 電源（最大值）:16.5mA 電流 - 輸出（最大值）:- 輸出類型:電流 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:800 |
| ATS693LSGTN-RSNYPH-T | 功能描述:IC HALL EFFECT SENSOR 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:專用型 技術:霍爾效應 極化:- 感應范圍:69% 跳閘，31% 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:4 V ~ 24 V 電流 - 電源（最大值）:16.5mA 電流 - 輸出（最大值）:- 輸出類型:電流 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:800 |
| ATS699LSN-FSWPH-T | 功能描述:2-WIRE DIFFERENTIAL SPEED & DIRE 制造商:allegro microsystems, llc 系列:- 零件狀態:在售 用于測量:旋轉位置 技術:電阻 旋轉角 - 電氣，機械:- 線性范圍:- 輸出:電阻 輸出信號:順時針增加 致動器類型:外磁鐵，不含 線性度:- 電阻容差:- 電壓 - 電源:4 V ~ 24 V 安裝類型:通孔 端子類型:焊接墊 工作溫度:-40°C ~ 150°C 標準包裝:2,400 |
| ATS699LSN-RSWPH-T | 功能描述:2-WIRE DIFFERENTIAL SPEED & DIRE 制造商:allegro microsystems, llc 系列:- 零件狀態:在售 用于測量:旋轉位置 技術:電阻 旋轉角 - 電氣，機械:- 線性范圍:- 輸出:電阻 輸出信號:順時針增加 致動器類型:外磁鐵，不含 線性度:- 電阻容差:- 電壓 - 電源:4 V ~ 24 V 安裝類型:通孔 端子類型:焊接墊 工作溫度:-40°C ~ 150°C 標準包裝:2,400 |
| ATS75 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LOW- OLTAGE 2-WIRE DIGITAL TEMPERATURE SENSOR With Thermal Alarm |
發布緊急采購，3分鐘左右您將得到回復。