- 您現在的位置：買賣IC網 > PDF目錄375378 > ATS674LSETN-LT-T (Allegro MicroSystems, Inc.) Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications PDF資料下載
參數資料
| 型號： | ATS674LSETN-LT-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| 中文描述： | 自校準聚烯烴齒傳感器優化的汽車凸輪傳感應用 |
| 文件頁數： | 1/20頁 |
| 文件大?。?/td> | 668K |
| 代理商： | ATS674LSETN-LT-T |
ATS673 and ATS674
ATS673LSE-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
AB SO LUTE MAX MUM RAT NGS
Supply Voltage,V
CC
...........................................
28 V
Reverse-Supply Voltage, V
RCC
........................
–18 V
Continuous Output Current, I
OUT
...................
20 mA
Reverse-Output Current, I
ROUT
.......................
50 mA
Operating Temperature
Ambient, T
A
, Range L................
–40oC to 150oC
Maximum Junction, T
J(max)
........................
165oC
Storage Temperature, T
S
..................
–65oC to 170oC
Tight timing accuracy over operating temperature range
True zero-speed operation
TPOS (True Power-On State)
Air-gap-independent switchpoints
High immunity to vibration
Large operating air gaps
Operation with supply voltages down to 3.3 V
Digital output representing target profile
Single-chip solution for high reliability
Optimized Hall IC/magnet system
AGC and reference adjust circuit
Undervoltage lockout
Recognizing the increasingly stringent requirements for EMC/EMI in automotive
applications, Allegro has taken the necessary steps to design devices that are
capable of withstanding the effects of radiated and conducted transients. The
ATS673 and ATS674 devices have been designed specifically for this purpose.
Advanced circuitry on the die allows them to survive positive and negative
transient pulses on both the input and output.
The ATS673 and ATS674 devices retain all of the same characteristics as the
ATS671 and ATS672. The devices remain true zero-speed gear tooth sensors with
optimized Hall IC/magnet configuration in an SIP (single in-line package). The
SIP assembly consists of a molded package that holds together a samarium cobalt
magnet, a pole piece, and a true zero-speed Hall IC that has been optimized to the
magnetic circuit.
The sensor incorporates a single element Hall IC that switches in response to
magnetic signals created by a ferrous target. The IC contains a sophisticated
digital circuit designed to eliminate the detrimental effects of magnet and system
offsets. Signal processing is used to provide zero-speed performance independent
of air gap and also to dynamically adapt device performance to the typical
operating conditions found in automotive applications, particularly cam sensing
applications (reduced vibration sensitivity).
High-resolution (9-bit) peak detecting DACs are used to set the adaptive switching
thresholds of the devices, ensuring high accuracy even in the presence of gear
eccentricity. Hysteresis in the thresholds reduces the negative effects of anomalies
in the magnetic signal (such as magnetic overshoot) associated with the targets
used in many automotive applications. The ATS673 and 674 also include a low
bandwidth filter that increases the noise immunity and the signal to noise ratio of
the sensor.
Two options are available for output polarity, low over tooth (LT) and high over
tooth (HT). For applications requiring absolute accuracy use the ATS674. The
ATS673 should be used for targets with high wobble.
Self-Calibrating TPOS Gear Tooth Sensor Optimized for
Automotive Cam Sensing Applications
Features and Benefits
Package SE, 4-pin Through Hole
1. VCC
2. VOUT
3. TEST
4. GND
1234
相關PDF資料 |
PDF描述 |
|---|---|
| ATS673LSETN-HT | Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATS673LSETN-HT-T | Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATS673LSETN-LT | Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATS673LSETN-LT-T | Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATTL7554AP | L7554 Low-Power SLIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS675LSE | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Self-Calibrating TPOS Speed Sensor Optimized for Automotive Cam Sensing Applications |
| ATS675LSETN-HT-T | 制造商:Allegro MicroSystems LLC 功能描述: |
| ATS675LSETN-LT-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS679532-1 | 制造商:APPLICATION TOOLING 功能描述: |
| ATS682LSH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Miniature, Two-Wire, True Zero Speed Differential Peak-Detecting Sensor IC |
發布緊急采購，3分鐘左右您將得到回復。