參數資料
型號: AT90PWM1-16MU
廠商: Atmel
文件頁數: 42/90頁
文件大小: 0K
描述: IC AVR PWM 8KB FLASH 16MHZ 32QFN
產品培訓模塊: megaAVR Introduction
標準包裝: 1
系列: AVR® 90PWM 照明
核心處理器: AVR
芯體尺寸: 8-位
速度: 16MHz
連通性: SPI
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 19
程序存儲器容量: 8KB(8K x 8)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 512 x 8
RAM 容量: 512 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 8x10b
振蕩器型: 內部
工作溫度: -40°C ~ 105°C
封裝/外殼: 32-VQFN 裸露焊盤
包裝: 標準包裝
其它名稱: AT90PWM1-16MUDKR
47
4378C–AVR–09/08
AT90PWM1
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the Reset flags to identify a reset condition, the user should read and then reset
the MCUSR as early as possible in the program. If the register is cleared before another reset
occurs, the source of the reset can be found by examining the reset flags.
9.1
Internal Voltage Reference
AT90PWM1 features an internal bandgap reference. This reference is used for Brown-out
Detection. It can also be used as a voltage reference for the DAC and/or the ADC, and can be
used as analog input for the analog comparators. In order to use the internal Vref, it is necessary
to configure it thanks to the REFS1 and REFS0 bits in the ADMUX register and to set an analog
feature which requires it.
9.1.1
Voltage Reference Enable Signals and Start-up Time
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in Table 9-4. To save power, the reference is not always turned on. The
reference is on during the following situations:
1.
When the BOD is enabled (by programming the BODLEVEL [2..0] Fuse).
2.
When the bandgap reference is connected to the Analog Comparator (by setting the
ACBG bit in ACSR).
3.
When the ADC is enabled.
4.
When the DAC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC or the DAC,
the user must always allow the reference to start up before the output from the Analog Compar-
ator or ADC or DAC is used. To reduce power consumption in Power-down mode, the user can
avoid the three conditions above to ensure that the reference is turned off before entering
Power-down mode.
9.1.2
Voltage Reference Characteristics
Note:
1. Values are guidelines only.
Table 9-4.
Internal Voltage Reference Characteristics(1)
Symbol
Parameter
Condition
Min.
Typ.
Max.
Units
VBG
Bandgap reference voltage
1.1
V
tBG
Bandgap reference start-up time
40
s
IBG
Bandgap reference current
consumption
15
A
相關PDF資料
PDF描述
AT89C4051-24PU IC MCU 4K FLASH 24MHZ 20-DIP
VE-B30-IX-F3 CONVERTER MOD DC/DC 5V 75W
ADG731BCPZ-REEL IC MULTIPLEXER 32X1 48LFCSP
ADG201HSKPZ-REEL IC SWITCH QUAD SPST 20PLCC
ADG707BRU IC MULTIPLEXER DUAL 8X1 28TSSOP
相關代理商/技術參數
參數描述
AT90PWM1-16MUR 功能描述:8位微控制器 -MCU AVR 8KFLASH 2PSC, 16MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90PWM1-16SE 制造商:Atmel Corporation 功能描述:
AT90PWM1-16SU 功能描述:8位微控制器 -MCU AVR 8Kflash 2PSC No DALI 16MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90PWM161-16MN 功能描述:8位微控制器 -MCU 16 MHz, QFN, 105oC, Green, RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90PWM161-16MNR 功能描述:8位微控制器 -MCU 16 MHz, QFN, 105oC, Green, T&R RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT