參數資料
型號： AT89C51ED2-SMRUM
廠商： Atmel
文件頁數： 99/137頁
文件大?。?/td> 0K
描述： IC MCU FLASH 8051 64K 5V 68PLCC
產品培訓模塊： MCU Product Line Introduction
標準包裝： 1
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 60MHz
連通性： SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 50
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 2K x 8
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-PLCC
包裝： 標準包裝
其它名稱： AT89C51ED2-SMRUMDKR
64
4235K–8051–05/08
AT89C51RD2/ED2
16.2.3
SPI Serial Clock (SCK)
This signal is used to synchronize the data movement both in and out of the devices through
their MOSI and MISO lines. It is driven by the Master for eight clock cycles which allows to
exchange one Byte on the serial lines.
16.2.4
Slave Select (SS)
Each Slave peripheral is selected by one Slave Select pin (SS). This signal must stay low for any
message for a Slave. It is obvious that only one Master (SS high level) can drive the network.
The Master may select each Slave device by software through port pins (Figure 16-2). To pre-
vent bus conflicts on the MISO line, only one slave should be selected at a time by the Master
for a transmission.
In a Master configuration, the SS line can be used in conjunction with the MODF flag in the SPI
Status register (SPSTA) to prevent multiple masters from driving MOSI and SCK (see Error
conditions).
A high level on the SS pin puts the MISO line of a Slave SPI in a high-impedance state.
The SS pin could be used as a general-purpose if the following conditions are met:
The device is configured as a Master and the SSDIS control bit in SPCON is set. This kind of
configuration can be found when only one Master is driving the network and there is no way
that the SS pin could be pulled low. Therefore, the MODF flag in the SPSTA will never be
set(1).
The Device is configured as a Slave with CPHA and SSDIS control bits set(2). This kind of
configuration can happen when the system comprises one Master and one Slave only.
Therefore, the device should always be selected and there is no reason that the Master uses
the SS pin to select the communicating Slave device.
Note:
1. Clearing SSDIS control bit does not clear MODF.
2. Special care should be taken not to set SSDIS control bit when CPHA = ’0’ because in this
mode, the SS is used to start the transmission.
16.2.5
Baud Rate
In Master mode, the baud rate can be selected from a baud rate generator which is controlled by
three bits in the SPCON register: SPR2, SPR1 and SPR0.The Master clock is selected from one
of seven clock rates resulting from the division of the internal clock by 2, 4, 8, 16, 32, 64 or 128.
Table 16-1 gives the different clock rates selected by SPR2:SPR1:SPR0.
Table 16-1.
SPI Master Baud Rate Selection
SPR2
SPR1
SPR0
Clock Rate
Baud Rate Divisor (BD)
0
F
CLK PERIPH /2
2
0
1
F
CLK PERIPH /4
4
0
1
0
F
CLK PERIPH/8
8
0
1
F
CLK PERIPH /16
16
1
0
F
CLK PERIPH /32
32
1
0
1
F
CLK PERIPH /64
64
1
0
F
CLK PERIPH /128
128
1
Don’t Use
No BRG
相關PDF資料
PDF描述
AT89C51IC2-RLRUM IC 8051 MCU 32K FLASH 44-VQFP
AT89C51ID2-RLRIM IC MCU FLASH 8051 64K 5V 44-VQFP
AT89C51RC-24PU IC MCU 32K FLASH 24MHZ 40-DIP
AT89C51RC2-RLRIL IC MCU FLASH 8051 32K 3V 44-VQFP
AT89C51RE2-SLRUM MCU 8051 128K FLASH 44-PLCC
相關代理商/技術參數
參數描述
AT89C51ED2-SMSIM 制造商:Atmel Corporation 功能描述:MCU 8-bit AT89 80C51 CISC 64KB Flash 3.3V/5V 68-Pin PLCC Stick 制造商:Atmel/Adesto Technologies 功能描述:Bulk 制造商:Atmel Corporation 功能描述:AT89C51ED2-SMSIM 8bit microcontroller
AT89C51ED2-SMSUM 功能描述:8位微控制器 -MCU C51ED2 64K FLASH 3-5.5V Ind RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C51ED2-UM 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51IC2 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with 2-wire Interface
AT89C51IC2_04 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with 2-wire Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*