參數資料
型號: AT89C4051-12PU
廠商: Atmel
文件頁數: 19/19頁
文件大?。?/td> 0K
描述: IC MCU 4K FLASH 12MHZ 20-DIP
產品培訓模塊: MCU Product Line Introduction
標準包裝: 18
系列: 89C
核心處理器: 8051
芯體尺寸: 8-位
速度: 12MHz
連通性: UART/USART
外圍設備: 欠壓檢測/復位,LED,POR
輸入/輸出數: 15
程序存儲器容量: 4KB(4K x 8)
程序存儲器類型: 閃存
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 6 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-DIP(0.300",7.62mm)
包裝: 管件
9
1001F–MICRO–6/08
AT89C4051
Program Verify: If lock bits LB1 and LB2 have not been programmed code data can be read
back via the data lines for verification:
1.
Reset the internal address counter to 000H by bringing RST from “L” to “H”.
2.
Apply the appropriate control signals for Read Code data and read the output data at
the port P1 pins.
3.
Pulse pin XTAL1 once to advance the internal address counter.
4.
Read the next code data byte at the port P1 pins.
5.
Repeat steps 3 and 4 until the entire array is read.
The lock bits cannot be verified directly. Verification of the lock bits is achieved by observing that
their features are enabled.
Chip Erase: The entire PEROM array (4K bytes) and the two Lock Bits are erased electrically
by using the proper combination of control signals and by holding P3.2 low for 10 ms. The code
array is written with all “1”s in the Chip Erase operation and must be executed before any non-
blank memory byte can be re-programmed.
Reading the Signature Bytes: The signature bytes are read by the same procedure as a nor-
mal verification of locations 000H, 001H, and 002H, except that P3.5 and P3.7 must be pulled to
a logic low. The values returned are as follows.
(000H) = 1EH indicates manufactured by Atmel
(001H) = 41H indicates AT89C4051
13. Programming Interface
Every code byte in the Flash array can be written and the entire array can be erased by using
the appropriate combination of control signals. The write operation cycle is self-timed and once
initiated, will automatically time itself to completion.
Most major worldwide programming vendors offer support for the Atmel AT89 microcontroller
series. Please contact your local programming vendor for the appropriate software revision.
Notes:
1. The internal PEROM address counter is reset to 000H on the rising edge of RST and is advanced by a positive pulse at
XTAL1 pin.
2. Chip Erase requires a 10-ms PROG pulse.
3. P3.1 is pulled Low during programming to indicate RDY/BSY.
13.1
Flash Programming Modes
Mode
RST/V
PP
P3.2/PROG
P3.3
P3.4
P3.5
P3.7
Write Code Data(1)(3)
12V
L
H
Read Code Data(1)
HH
L
H
Write Lock
Bit - 1
12V
HH
Bit - 2
12V
H
L
Chip Erase
12V
H
L
Read Signature Byte
H
L
(2)
相關PDF資料
PDF描述
ADG509FBRN IC MULTIPLEXER DUAL 4X1 16SOIC
VI-B22-IX-F3 CONVERTER MOD DC/DC 15V 75W
VI-B22-IX-F1 CONVERTER MOD DC/DC 15V 75W
ATMEGA324A-CUR IC MCU AVR 32K 20MHZ 49VFBGA
VI-B22-IW-F4 CONVERTER MOD DC/DC 15V 100W
相關代理商/技術參數
參數描述
AT89C4051-12PU-RET 制造商:Atmel Corporation 功能描述:
AT89C4051-12SA 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash
AT89C4051-12SC 功能描述:8位微控制器 -MCU 8051 4K FLASH 2.7 TO 5.5V 12MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C4051-12SI 功能描述:8位微控制器 -MCU 8051 4K FLASH 2.7 TO 5.5V 12MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89C4051-12SU 功能描述:8位微控制器 -MCU 8051 4K FLASH 2.7 TO 5.5V 12MHZ 4V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT