參數資料
型號： AS5130-ASST-500
廠商： ams
文件頁數： 22/33頁
文件大?。?/td> 4323K
描述： IC ENCODER ROTORY 8-BIT 16-SSOP
標準包裝： 500
傳感范圍： 32mT ~ 75mT
類型： 線性，旋轉編碼器 - 可編程
電源電壓： 4.5 V ~ 5.5 V
電流 - 電源： 24mA
輸出類型： 模擬，比率
特點： 可編程
工作溫度： -40°C ~ 125°C
封裝/外殼： *
供應商設備封裝： *
包裝： *
www.austriamicrosystems.com/AS5130
Revision 1.12
21 - 41
AS5130
Datasheet - Detailed Description
7.7 High Speed Operation
The AS5130 is using a fast tracking ADC (TADC) to determine the angle of the magnet. The TADC has a tracking rate of 1.15祍 (typ).
Once the TADC is synchronized with the angle, it sets the LOCK bit in the status register (see Table 9). In worst case, usually at start-up, the
TADC requires a maximum of 127 steps (127 * 1.15礢 = 146.05祍) to lock. Once it is locked, it requires only one cycle (1.15祍) to track the
moving magnet.
The AS5130 can operate in locked mode at rotational speeds up to 30,000 rpm.
In Low Power Mode, the position of the TADC is frozen. It will continue from the frozen position once it is powered up again. If the magnet has
moved during the power down phase, several cycles will be required before the TADC is locked again. The tracking time to lock in with the new
magnet angle can be roughly calculated as:
t
LOCK
 = 1.15祍* |NewPos  OldPos|
(EQ 3)
Where:
t
LOCK
 = time required to acquire the new angle after power up from one of the reduced power modes [祍]
OldPos = Angle position when one of the reduced power modes is activated [篯
NewPos = Angle position after resuming from reduced power mode [篯
7.7.1   Propagation Delay
The Propagation delay is the time required from reading the magnetic field by the Hall sensors to calculating the angle and making it available on
the serial or PWM interface. While the propagation delay is usually negligible on low speeds, it is an important parameter at high speeds. The
longer the propagation delay, the larger becomes the angle error for a rotating magnet as the magnet is moving while the angle is calculated. The
position error increases linearly with speed. The main factors that contribute to the propagation delay are discussed in detail further in this
document.
7.7.2   Sampling Rate
For high speed applications, fast ADCs are essential. The ADC sampling rate directly influences the propagation delay. The fast tracking ADC
used in the AS5130 with a tracking rate of only 1.15祍 (typ) is a perfect fit for both high speed and high performance.
7.7.3   Chip Internal Lowpass Filtering
A commonplace practice for systems using analog-to-digital converters is to filter the input signal by an anti-aliasing filter. The filter characteristic
must be chosen carefully to balance propagation delay and noise. The lowpass filter in the AS5130 has a cutoff frequency of typ. 23.8kHz and
the overall propagation delay in the analog signal path is typ. 15.6祍.
7.7.4   Digital Readout Rate
Aside from the chip-internal propagation delay, the time required to read and process the angle data must also be considered. Due to its nature,
a PWM signal is not very usable at high speeds, as you get only one reading per PWM period. Increasing the PWM frequency may improve the
situation but causes problems for the receiving controller to resolve the PWM steps. The frequency on the AS5130 PWM output is typ. 1.95kHz
with a resolution of 2祍/step. A more suitable approach for high speed absolute angle measurement is using the serial interface. With a clock
rate of up to 6MHz, a complete set of data (21bits) can be read in >3.5祍.
7.7.5   Total Propagation Delay of the AS5130
The total propagation delay of the AS5130 is the delay in the analog signal path and the tracking rate of the ADC:
15.6祍 + 1.15祍 = 16.75祍
(EQ 4)
If only the SIN-/COS-outputs are used, the propagation delay is the analog signal path delay only (typ. 15.6祍).
Position Error Over Speed: The angle error over speed caused by the propagation delay is calculated as:
敻
pd
 = rpm * 6 * 16.75E
-6
  in degrees
(EQ 5)
In addition, the anti-aliasing filter causes an angle error calculated as:
?SPAN class="pst AS5130-ASST-500_2599059_9">?/SPAN>
lpf
 = ArcTan [rpm / (60*f0)]
(EQ 6)
Table 12. Examples of the Overall Position Error caused by Speed (includes both propagation delay and filter delay)
Speed (rpm)
Total Position Error (?/SPAN>?/SPAN>
pd +
?SPAN class="pst AS5130-ASST-500_2599059_9">?/SPAN>
lpf
)
100
0.0175?/DIV>
相關PDF資料
PDF描述
AS5132-HSST-500 IC ENCODER ROTARY 20-SSOP
AS5134-ZSST-500 IC ENCODER RPTARY 20-SSOP
AS5140H-ASST IC ENCODER ROTARY 10BIT 16-SSOP
AS5145B-HSST-500 IC ENCODER ROTARY MAGN 16-SSOP
AS5510-DWLT IC ENCODER MAGNETIC LIN 6-WLCSP
相關代理商/技術參數
參數描述
AS5130ASSU 制造商:AMS 功能描述:IC MAGNETIC ROTARY ENCODER 8BIT SSOP-16 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 8BIT SSOP-16; IC Function:Encoder IC; Brief Features:360 Contactless Angular Position Encoding, Two Digital 8-bit Absolute Output; Supply Voltage Min:3V; Supply Voltage Max:5.5V; No. of Pins:16 ;RoHS Compliant: Yes
AS5130-ASSU 功能描述:IC ENCODER ROTARY 8-BIT 16-SSOP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
AS5130ATST 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:8 Bit Programmable Magnetic Rotary Encoder with Motion Detection & Multiturn
AS5130ATSU 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:8 Bit Programmable Magnetic Rotary Encoder with Motion Detection & Multiturn
AS5130-SS_EK_DB 功能描述:AS5130 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件狀態:有效 傳感器類型:磁性，旋轉位置 感應范圍:360° 接口:串行 靈敏度:- 電壓 - 電源:4.5 V ~ 5.5 V 嵌入式:- 所含物品:板 使用的 IC/零件:AS5130 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*