- 您現在的位置：買賣IC網 > PDF目錄375359 > ARA05050 (ANADIGICS INC) Reverse Amplifier with Step Attenuator PDF資料下載
參數資料
| 型號： | ARA05050 |
| 廠商： | ANADIGICS INC |
| 元件分類： | 衰減器 |
| 英文描述： | Reverse Amplifier with Step Attenuator |
| 中文描述： | 5 MHz - 100 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| 封裝： | SSOP-28 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 562K |
| 代理商： | ARA05050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁
10
Data Sheet - Rev 2.2
05/2005
ARA05050
APPLICATION INFORMATION
Printed Circuit Board Layout Considerations
The ARA05050 is a high-performance RF device.
Special consideration must be given to certain
features of the the printed circuit board layout, as
they can affect the RF performance of the IC. Refer to
the ANADIGICS application note “CATV Reverse Amp
w/ Step Attenuator” for more details.
Amplifier Enable / Disable
The ARA05050 includes two amplification stages that
each can be shut down through external control pins
V
REF
1
and V
REF
2
(pins 5 and 19, respectively.) By
applying a typical bias of 1.75 Volts to these pins, the
amplifiers are enabled. In order to fully disable an
amplifier, its control pin requires a negative bias of
-1.5 to -2.0 Volts.
Amplifier Bias Current
The I
SET
pins (11 and 25) set the bias current for the
amplification stages. Grounding these pins results
in the maximum possible current. By placing a
resistor from the pin to ground, the current can be
reduced. The recommended bias conditions use
the configuration shown in the test circuit schematic
in Figure 4.
Thermal Layout Considerations
The device package for the ARA05050 features a heat
slug on the bottom of the package body. Use of the
heat slug is an integral part of the device design.
Soldering it to the ground plane of the PC board will
ensure the lowest possible thermal resistance for
the device, and will result in the longest MTF (mean
time to failure.)
A PC board layout that optimizes the benefits of the
heat slug is shown in Figure 13. The via holes located
under the body of the device must be plated through
to a ground plane layer of metal, in order to provide
sufficient thermal conductivity. The recommended
solder mask outline is shown in Figure 14.
ESD Sensitivity
Electrostatic discharges can cause permanent
damage to this device. Electrostatic charges
accumulate on test equipment and the human body,
and can discharge without detection. Proper
precautions
and
handling
recommended. Refer to the ANADIGICS application
note on ESD precautions.
are
strongly
Figure 13: PC Board Layout
相關PDF資料 |
PDF描述 |
|---|---|
| ARA05050RS12P1 | Reverse Amplifier with Step Attenuator |
| ARA1400S12 | ER 3C 3#8 SKT RECP |
| ARA2000S23 | ER 6C 3#16 3#8 SKT RECP WALL |
| ARA2000 | Address-Programmable Reverse Amplifier with Step Attenuator |
| ARA2000S12P1 | Address-Programmable Reverse Amplifier with Step Attenuator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ARA05050_12 | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:Reverse Amplifier with Step Attenuator |
| ARA05050RS12P1 | 制造商:ANADIGICS Inc 功能描述:BROADBAND/CATV (75 OHM) REVERSE AMPLIFIER |
| ARA05050S12 | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:CATV Reverse Amplifier w/step Attenuator |
| ARA05050S12-1 | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:CATV Reverse Amplifier w/step Attenuator |
| ARA05050S12C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous |
發布緊急采購，3分鐘左右您將得到回復。