ProASICPLUS Flash Family FPGAs 2- 20 v5.9 User Security ProASIC" />
參數資料
型號： APA750-FGG676I
廠商： Microsemi SoC
文件頁數： 103/178頁
文件大小： 0K
描述： IC FPGA PROASIC+ 750K 676-FBGA
標準包裝： 40
系列： ProASICPLUS
RAM 位總計： 147456
輸入/輸出數： 454
門數： 750000
電源電壓： 2.3 V ~ 2.7 V
安裝類型： 表面貼裝
工作溫度： -40°C ~ 85°C
封裝/外殼： 676-BGA
供應商設備封裝： 676-FBGA（27x27）
ProASICPLUS Flash Family FPGAs
2- 20
v5.9
User Security
ProASICPLUS devices have FlashLock protection bits that,
once
programmed,
block
the
entire
programmed
contents from being read externally. Refer to Table 2-11
for details on the number of bits in the key for each
device. If locked, the user can only reprogram the device
employing the user-defined security key. This protects
the device from being read back and duplicated. Since
programmed data is stored in nonvolatile memory cells
(actually very small capacitors) rather than in the wiring,
physical deconstruction cannot be used to compromise
data. This type of security breach is further discouraged
by the placement of the memory cells beneath the four
metal layers (whose removal cannot be accomplished
without disturbing the charge in the capacitor). This is
the highest security provided in the industry. For more
information,
refer
to
Actel’s
Embedded Memory Floorplan
The embedded memory is located across the top and
bottom of the device in 256x9 blocks (Figure 1-1 on page
1-2). Depending on the device, up to 88 blocks are
available to support a variety of memory configurations.
Each block can be programmed as an independent
memory array or combined (using dedicated memory
routing resources) to form larger, more complex memory
configurations. A single memory configuration could
include blocks from both the top and bottom memory
locations.
Embedded Memory Configurations
The embedded memory in the ProASICPLUS family
provides great configuration flexibility (Table 2-12). Each
ProASICPLUS block is designed and optimized as a two-
port memory (one read, one write). This provides 198
kbits of two-port and/or single port memory in the
APA1000 device.
Each memory block can be configured as FIFO or SRAM,
with
independent
selection
of
synchronous
or
asynchronous
read
and
write
ports
Additional characteristics include programmable flags as
well as parity checking and generation. Figure 2-18 on
diagrams of the basic SRAM and FIFO blocks. Table 2-14
memory
block
SRAM
and
FIFO
interface
signals,
respectively. A single memory block is designed to
operate at up to 150 MHz (standard speed grade typical
conditions). Each block is comprised of 256 9-bit words
(one read port, one write port). The memory blocks may
be cascaded in width and/or depth to create the desired
memory organization. (Figure 2-20 on page 2-24). This
provides optimal bit widths of 9 (one block), 18, 36, and
72, and optimal depths of 256, 512, 768, and 1,024. Refer
to Actel’s SmartGen User’s Guide for more information.
Figure 2-21 on page 2-24 gives an example of optimal
memory usage. Ten blocks with 23,040 bits have been
used to generate three arrays of various widths and
depths. Figure 2-22 on page 2-24 shows how RAM blocks
can be used in parallel to create extra read ports. In this
example, using only 10 of the 88 available blocks of the
APA1000 yields an effective 6,912 bits of multiple port
RAM. The Actel SmartGen software facilitates building
wider and deeper memory configurations for optimal
memory usage.
Table 2-11 Flashlock Key Size by Device
Device
Key Size
APA075
79 bits
APA150
79 bits
APA300
79 bits
APA450
119 bits
APA600
167 bits
APA750
191 bits
APA1000
263 bits
Table 2-12 ProASICPLUS Memory Configurations by Device
Device
Bottom
Top
Maximum Width
Maximum Depth
DWDW
APA075
0
12
256
108
1,536
9
APA150
0
16
256
144
2,048
9
APA300
16
256
144
2,048
9
APA450
24
256
216
3,072
9
APA600
28
256
252
3,584
9
APA750
32
256
288
4,096
9
APA1000
44
256
396
5,632
9
相關PDF資料
PDF描述
HSC43DRAS-S734 CONN EDGECARD 86POS .100 R/A PCB
EP2SGX30DF780I4N IC STRATIX II GX 30K 780-FBGA
25AA160CT-I/MNY IC SRL EEPROM 2KX8 1.8V 8-TDFN
ACC49DRXI-S734 CONN EDGECARD 98POS DIP .100 SLD
EP1S25F672C6N IC STRATIX FPGA 25K LE 672-FBGA
相關代理商/技術參數
參數描述
APA750-FGG896 功能描述:IC FPGA PROASIC+ 750K 896-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP，帶拉桿 供應商設備封裝:352-CQFP（75x75）
APA750-FGG896A 功能描述:IC FPGA PROASIC+ 750K 896-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP，帶拉桿 供應商設備封裝:352-CQFP（75x75）
APA750-FGG896I 功能描述:IC FPGA PROASIC+ 750K 896-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ProASICPLUS 標準包裝:1 系列:ProASICPLUS LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:129024 輸入/輸出數:248 門數:600000 電源電壓:2.3 V ~ 2.7 V 安裝類型:表面貼裝 工作溫度:- 封裝/外殼:352-BFCQFP，帶拉桿 供應商設備封裝:352-CQFP（75x75）
APA750-FGGB 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA750-FGGES 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*