參數資料
型號: ADUM1412BRWZ
廠商: ANALOG DEVICES INC
元件分類: 其它接口
英文描述: Quad-Channel Digital Isolators
中文描述: SPECIALTY INTERFACE CIRCUIT, PDSO16
封裝: ROHS COMPLIANT, MS-013AA, SOIC-16
文件頁數: 9/20頁
文件大小: 277K
代理商: ADUM1412BRWZ
ADuM1410/ADuM1411/ADuM1412
Parameter
Input Disable Time
9
Input Dynamic Supply Current per Channel
10
5 V Operation
3 V Operation
Output Dynamic Supply Current per Channel
10
5 V Operation
3 V Operation
1
All voltages are relative to their respective ground.
2
The supply current values for all four channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section.
See Figure 8 through Figure 10 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 11 through
Figure 15 for total V
DD1
and V
DD2
supply currents as a function of data rate for ADuM1410/ADuM1411/ADuM1412 channel configurations.
3
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
4
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
5
t
PHL
propagation delay is measured from the 50% level of the falling edge of the V
Ix
signal to the 50% level of the falling edge of the V
Ox
signal. t
PLH
propagation delay is
measured from the 50% level of the rising edge of the V
Ix
signal to the 50% level of the rising edge of the V
Ox
signal.
6
t
PSK
is the magnitude of the worst-case difference in t
PHL
or t
PLH
that is measured between units at the same operating temperature, supply voltages, and output load
within the recommended operating conditions.
7
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
8
CM
H
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
O
> 0.8 V
DD2
. CM
L
is the maximum common-mode voltage slew rate
that can be sustained while maintaining V
O
< 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
9
Input enable time is the duration from when V
DISABLE
is set low until the output states are guaranteed to match the input states in the absence of any input data logic
transitions. If an input data logic transition within a given channel does occur within this time interval, the output of that channel reaches the correct state within the
much shorter duration as determined by the propagation delay specifications within this data sheet. Input disable time is the duration from when V
DISABLE
is set high
until the output states are guaranteed to reach their programmed output levels, as determined by the CTRL logic state (See Table 10).
10
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 8 through Figure 10 for information
on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section for guidance on calculating the per-channel supply current
for a given data rate.
Rev. E | Page 9 of 20
Symbol
t
DISABLE
I
DDI (D)
I
DDI (D)
Min
Typ
5.0
0.12
0.07
0.04
0.02
Max Unit
Test Conditions
V
IA
, V
IB
, V
IC
, V
ID
= 0 or V
DD1
mA/Mbps
mA/Mbps
mA/Mbps
mA/Mbps
μs
相關PDF資料
PDF描述
ADUM1412BRWZ-RL Quad-Channel Digital Isolators
ADUM2250 Hot-Swappable, Dual I2C Isolators, 5 kV
ADUM2250ARWZ Hot-Swappable, Dual I2C Isolators, 5 kV
ADUM2250ARWZ-RL Hot-Swappable, Dual I2C Isolators, 5 kV
ADuM2251 Hot-Swappable, Dual I2C Isolators, 5 kV
相關代理商/技術參數
參數描述
ADUM1412BRWZ 制造商:Analog Devices 功能描述:DIGITAL ISOLATOR, 4CH, 30NS, WSOIC-16
ADUM1412BRWZ-RL 功能描述:IC ISOLATOR DGTL QUAD 16-SOIC RoHS:是 類別:隔離器 >> 數字隔離器 系列:iCoupler® 產品培訓模塊:IsoLoop® Isolator 標準包裝:50 系列:IsoLoop® 輸入 - 1 側/2 側:5/0 通道數:5 電源電壓:3 V ~ 5.5 V 電壓 - 隔離:2500Vrms 數據速率:110Mbps 傳輸延遲:12ns 輸出類型:CMOS 封裝/外殼:16-SOIC(0.154",3.90mm 寬) 供應商設備封裝:16-SOIC N 包裝:管件 工作溫度:-40°C ~ 85°C 其它名稱:390-1053-5
ADUM141D0BRQZ 功能描述:DGTL ISO ROBUST QUAD 3:1 CH 制造商:analog devices inc. 系列:iCoupler? 包裝:管件 零件狀態:在售 技術:磁耦合 類型:通用 隔離式電源:無 通道數:4 輸入 - 輸入側 1/輸入側 2:3/1 通道類型:單向 電壓 - 隔離:3000Vrms 共模瞬態抗擾度(最小值):75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL(最大值):13ns,13ns 脈寬失真(最大):3ns 上升/下降時間(典型值):2.5ns,2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SSOP(0.154",3.90mm 寬) 供應商器件封裝:16-QSOP 標準包裝:98
ADUM141D0BRQZ-RL7 功能描述:DGTL ISO ROBUST QUAD 3:1 CH 制造商:analog devices inc. 系列:iCoupler? 包裝:帶卷(TR) 零件狀態:在售 技術:磁耦合 類型:通用 隔離式電源:無 通道數:4 輸入 - 輸入側 1/輸入側 2:3/1 通道類型:單向 電壓 - 隔離:3000Vrms 共模瞬態抗擾度(最小值):75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL(最大值):13ns,13ns 脈寬失真(最大):3ns 上升/下降時間(典型值):2.5ns,2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SSOP(0.154",3.90mm 寬) 供應商器件封裝:16-QSOP 標準包裝:1,000
ADUM141D0BRWZ 功能描述:General Purpose Digital Isolator 3750Vrms 4 Channel 150Mbps 75kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:analog devices inc. 系列:iCoupler? 包裝:管件 零件狀態:有效 技術:磁耦合 類型:通用 隔離式電源:無 通道數:4 輸入 - 輸入側 1/輸入側 2:3/1 通道類型:單向 電壓 - 隔離:3750Vrms 共模瞬態抗擾度(最小值):75kV/μs 數據速率:150Mbps 傳播延遲 tpLH / tpHL(最大值):13ns,13ns 脈寬失真(最大):3ns 上升/下降時間(典型值):2.5ns,2.5ns 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商器件封裝:16-SOIC 標準包裝:47