- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC831BCPZ (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC831BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 42/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | PSM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 數據轉換器： | A/D 8x12b，D/A 2x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
| 配用： | EVAL-ADUC831QSZ-ND - KIT DEV FOR ADUC831 QUICK START |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
REV. 0
ADuC831
–47–
8052 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are mostly 8052 compatible (with a
few additional features) and are controlled via standard 8052
SFR bit definitions.
Parallel I/O
The ADuC831 uses four input/output ports to exchange data
with external devices. In addition to performing general-purpose
I/O, some ports are capable of external memory operations while
others are multiplexed with alternate functions for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0
Port 0 is an 8-bit, open-drain, bidirectional I/O port that is directly
controlled via the Port 0 SFR. Port 0 is also the multiplexed
low-order address and data bus during accesses to external pro-
gram or data memory.
Figure 36 shows a typical bit latch and I/O buffer for a Port 0
port pin. The bit latch (one bit in the port’s SFR) is represented
as a Type D flip-flop, which will clock in a value from the inter-
nal bus in response to a “write to latch” signal from the CPU.
The Q output of the flip-flop is placed on the internal bus in
response to a “read latch” signal from the CPU. The level of the
port pin itself is placed on the internal bus in response to a
“read pin” signal from the CPU. Some instructions that read a
port activate the “read latch” signal, and others activate the
“read pin” signal. See the following Read-Modify-Write Instruc-
tions section for more details.
CONTROL
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
DVDD
ADDR/DATA
P0.x
PIN
Figure 36. Port 0 Bit Latch and I/O Buffer
As shown in Figure 36, the output drivers of Port 0 pins are
switchable to an internal ADDR and ADDR/DATA bus by an
internal CONTROL signal for use in external memory accesses.
During external memory accesses the P0 SFR gets 1s written to it
(i.e., all of its bit latches become 1). When accessing external
memory, the CONTROL signal in Figure 36 goes high, enabling
push-pull operation of the output pin from the internal address or
data bus (ADDR/DATA line). Therefore, no external pull-ups are
required on Port 0 in order for it to access external memory.
In general-purpose I/O port mode, Port 0 pins that have 1s written
to them via the Port 0 SFR will be configured as “open drain”
and will therefore float. In this state, Port 0 pins can be used as
high impedance inputs. This is represented in Figure 36 by the
NAND gate whose output remains high as long as the CONTROL
signal is low, thereby disabling the top FET. External pull-up
resistors are therefore required when Port 0 pins are used as
general-purpose outputs. Port 0 pins with 0s written to them
will drive a logic low output voltage (VOL) and will be capable of
sinking 1.6 mA.
Port 1
Port 1 is also an 8-bit port directly controlled via the P1 SFR.
Port 1 digital output capability is not supported on this device.
Port 1 pins can be configured as digital inputs or analog inputs.
By (power-on) default these pins are configured as analog
inputs, i.e., 1 written in the corresponding Port 1 register bit.
To configure any of these pins as digital inputs, the user should
write a 0 to these port bits to configure the corresponding pin as
a high impedance digital input.
These pins also have various secondary functions described in
Table XVII.
Table XVII. Port 1, Alternate Pin Functions
Pin
Alternate Function
P1.0
T2 (Timer/Counter 2 External Input)
P1.1
T2EX (Timer/Counter 2 Capture/Reload Trigger)
P1.5
SS (Slave Select for the SPI Interface)
READ
LATCH
INTERNAL
BUS
WRITE
TO LATCH
READ
PIN
D
CL
Q
LATCH
P1.x
PIN
TO ADC
Figure 37. Port 1 Bit Latch and I/O Buffer
Port 2
Port 2 is a bidirectional port with internal pull-up resistors
directly controlled via the P2 SFR. Port 2 also emits the high
order address bytes during fetches from external program memory
and middle and high order address bytes during accesses to the
24-bit external data memory space.
As shown in Figure 38, the output drivers of Ports 2 are switchable
to an internal ADDR and ADDR/DATA bus by an internal
CONTROL signal for use in external memory accesses (as for
Port 0). In external memory addressing mode (CONTROL = 1)
the port pins feature push-pull operation controlled by the inter-
nal address bus (ADDR line). However, unlike the P0 SFR
during external memory accesses, the P2 SFR remains unchanged.
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC831BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC831BS | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +12BIT ADC LQFP52 831 |
| ADUC831BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP T/R |
| ADUC831BSZ | 功能描述:IC ADC/DAC 12BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC831BSZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發布緊急采購，3分鐘左右您將得到回復。