參數資料
型號： ADSP-21990
廠商： Analog Devices, Inc.
元件分類： 數字信號處理
英文描述： 16-bit fixed point DSP with Flash
中文描述： 具有閃存的 16 位定點 DSP
文件頁數： 10/44頁
文件大?。?/td> 574K
代理商： ADSP-21990
ADSP-21990
–10–
REV. 0
The encoder interface unit can also be made to implement some
error checking functions. If an encoder count error is detected
(due to a disconnected encoder line, for example), a status bit in
the EIUSTAT register is set, and an EIU count error interrupt is
generated.
The encoder interface unit of the ADSP-21990 contains a 16-bit
loop timer that consists of a timer register, period register and
scale register so that it can be programmed to time out and reload
at appropriate intervals. When this loop timer times out, an EIU
loop timer timeout interrupt is generated. This interrupt could
be used to control the timing of speed and position control loops
in high performance drives.
The encoder interface unit also includes a high performance
encoder event timer (EET) block that permits the accurate timing
of successive events of the encoder inputs. The EET can be pro-
grammed to time the duration between up to 255 encoder pulses
and can be used to enhance velocity estimation, particularly at
low speeds of rotation.
Flag I/O (FIO) Peripheral Unit
The FIO module is a generic parallel I/O interface that supports
sixteen bidirectional multifunction flags or general-purpose
digital I/O signals (PF15–0).
All sixteen FLAG bits can be individually configured as an input
or output based on the content of the direction (DIR) register,
and can also be used as an interrupt source for one of two FIO
interrupts. When configured as input, the input signal can be
programmed to set the FLAG on either a level (level sensitive
input/interrupt) or an edge (edge sensitive input/interrupt).
The FIO module can also be used to generate an asynchronous
unregistered wake-up signal FIO_WAKEUP for DSP core wake
up after power-down.
The FIO Lines, PF7–1 can also be configured as external slave
select outputs for the SPI communications port, while PF0 can
be configured to act as a slave select input.
The FIO Lines can be configured to act as a PWM shutdown
source for the 3-phase PWM generation unit of the
ADSP-21990.
Watchdog Timer
The ADSP-21990 integrates a watchdog timer that can be used
as a protection mechanism against unintentional software events.
It can be used to cause a complete DSP and peripheral reset in
such an event. The watchdog timer consists of a 16-bit timer that
is clocked at the external clock rate (CLKIN or crystal input
frequency).
In order to prevent an unwanted timeout or reset, it is necessary
to periodically write to the watchdog timer register. During
abnormal system operation, the watchdog count will eventually
decrement to 0 and a watchdog timeout will occur. In the system,
the watchdog timeout will cause a full reset of the DSP core and
peripherals.
General-Purpose Timers
The ADSP-21990 contains a general-purpose timer unit that
contains three identical 32-bit timers. The three programmable
interval timers (Timer0, Timer1, and Timer2) generate periodic
interrupts. Each timer can be independently set to operate in one
of three modes:
Pulse Waveform Generation (PWM_OUT) mode
Pulsewidth Count/Capture (WDTH_CAP) mode
External Event Watchdog (EXT_CLK) mode
Each Timer has one bidirectional chip pin, TMR2-0. For each
timer, the associated pin is configured as an output pin in
PWM_OUT Mode and as an input pin in WDTH_CAP and
EXT_CLK Modes.
Interrupts
The interrupt controller lets the DSP respond to 17 interrupts
with minimum overhead. The DSP core implements an interrupt
priority scheme as shown in
Table 2
. Applications can use the
unassigned slots for software and peripheral interrupts. The
Peripheral Interrupt Controller is used to assign the various
peripheral interrupts to the 12 user assignable interrupts of the
DSP core.
There is no assigned priority for the peripheral interrupts after
reset. To assign the peripheral interrupts a different priority,
applications write the new priority to their corresponding control
bits (determined by their ID) in the Interrupt Priority Control
register.
Interrupt routines can either be nested with higher priority inter-
rupts taking precedence or processed sequentially. Interrupts can
be masked or unmasked with the IMASK register. Individual
interrupt requests are logically ANDed with the bits in IMASK;
the highest priority unmasked interrupt is then selected. The
emulation, power down, and reset interrupts are nonmaskable
with the IMASK register, but software can use the DIS INT
instruction to mask the power-down interrupt.
The Interrupt Control (ICNTL) register controls interrupt
nesting and enables or disables interrupts globally.
The IRPTL register is used to force and clear interrupts. On-chip
stacks preserve the processor status and are automatically main-
tained during interrupt handling. To support interrupt, loop, and
subroutine nesting, the PC stack is 33 levels deep, the loop stack
is 8 levels deep, and the status stack is 16 levels deep. To prevent
stack overflow, the PC stack can generate a stack level interrupt
if the PC stack falls below 3 locations full or rises above 28
locations full.
The following instructions globally enable or disable interrupt
servicing, regardless of the state of IMASK.
ENA INT;
DIS INT;
At reset, interrupt servicing is disabled.
For quick servicing of interrupts, a secondary set of DAG and
computational registers exist. Switching between the primary
and secondary registers lets programs quickly service interrupts,
while preserving the state of the DSP.
相關PDF資料
PDF描述
ADSP-21990BBC 16-bit fixed point DSP with Flash
ADSP-21990BST 16-bit fixed point DSP with Flash
ADSP-21MOD870-100 Single Chip Digital Modem(單片數字調制解調器)
ADSP-21MOD870-110 Internet Gateway Processor Software
ADSP-21MOD870 Internet Gateway Processor
相關代理商/技術參數
參數描述
ADSP-21990BBC 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA 制造商:Rochester Electronics LLC 功能描述:160 MIPS, MIXED SIGNAL DSPWITH 14-BIT - Bulk
ADSP-21990BST 制造商:Rochester Electronics LLC 功能描述:160 MIPS,MIXED SIGNAL DSP WITH 14BIT - Tape and Reel
ADSP-21990BSTZ 功能描述:IC DSP CONTROLLER 16BIT 176-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21991BBC 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA
ADSP-21991BBCZ 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*