- 您現在的位置：買賣IC網 > PDF目錄374031 > ADS1000A1IDBVRG4 (Analog Devices, Inc.) LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE PDF資料下載
參數資料
| 型號： | ADS1000A1IDBVRG4 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
| 中文描述： | 低功耗，12位模擬數字轉換接口的I2C⑩ |
| 文件頁數： | 14/17頁 |
| 文件大小： | 240K |
| 代理商： | ADS1000A1IDBVRG4 |
www.ti.com
ADDITIONAL RECOMMENDATIONS
The ADS1000 is fabricated in a small-geometry
low-voltage process. The analog inputs feature
protection diodes to the supply rails. However, the
current-handling ability of these diodes is limited, and
the ADS1000 can be permanently damaged by
analog
input
voltages
that
approximately 300mV beyond the rails for extended
periods. One way to protect against overvoltage is to
place current-limiting resistors on the input lines. The
ADS1000 analog inputs can withstand momentary
currents of as large as 10mA.
The previous paragraph does not apply to the I
2
C
ports, which can both be driven to 6V regardless of
the supply.
ADS1000
SBAS357–SEPTEMBER 2006
stabilized; this momentary spike can damage the
ADS1000. Sometimes this damage is incremental
and results in slow, long-term failure—which can be
distastrous
for
permanently
maintenance systems.
installed,
low-
If using an op amp or other front-end circuitry with
the ADS1000, be sure to take the performance
characteristics of this circuitry into account; a chain is
only as strong as its weakest link.
remain
more
than
Any data converter is only as good as its reference.
For the ADS1000, the reference is the power supply,
and the power supply must be clean enough to
achieve the desired performance. If a power-supply
filter capacitor is used, it should be placed close to
the V
DD
pin, with no vias placed between the
capacitor and the pin. The trace leading to the pin
should be as wide as possible, even if it must be
necked down at the device.
If the ADS1000 is driven by an op amp with high
voltage supplies, such as
±
12V, protection should be
provided, even if the op amp is configured so that it
will not output out-of-range voltages. Many op amps
seek to one of the supply rails immediately when
power is applied, usually before the input has
14
相關PDF資料 |
PDF描述 |
|---|---|
| ADS1000A1IDBVT | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
| ADS1000A1IDBVTG4 | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
| ADS1000 | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
| ADS1000A0IDBVR | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
| ADS1000A0IDBVRG4 | LOW POWER, 12-Bit ANALOG-TO-DIGITAL CONVERTER with I2C⑩ INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS1000A1IDBVT | 功能描述:模數轉換器 - ADC 12-Bit ADC with I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1000A1IDBVT | 制造商:Texas Instruments 功能描述:A/D Converter (A-D) IC |
| ADS1000A1IDBVTG4 | 功能描述:模數轉換器 - ADC 12-Bit ADC with I2C Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1000A1QDBVRQ1 | 功能描述:模數轉換器 - ADC Auto Cat Low Cost 12B ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1000AOIDBVT | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。