參數資料
型號： ADR433A
廠商： Analog Devices, Inc.
英文描述： Ultralow Noise XFET Voltage References with Current Sink and Source Capability
中文描述： 超低噪聲XFET電壓基準與電流吸入和源能力
文件頁數： 15/24頁
文件大?。?/td> 868K
代理商： ADR433A
ADR430/ADR431/ADR433/ADR434/ADR435/ADR439
THEORY OF OPERATION
The ADR43x series of references uses a new reference generation
technique known as XFET (eXtra implanted junction FET).
This technique yields a reference with low supply current, good
thermal hysteresis, and exceptionally low noise. The core of the
XFET reference consists of two junction field-effect transistors
(JFETs), one of which has an extra channel implant to raise its
pinch-off voltage. By running the two JFETs at the same drain
current, the difference in pinch-off voltage can be amplified and
used to form a highly stable voltage reference.
Rev. B | Page 15 of 24
The intrinsic reference voltage is around 0.5 V with a negative
temperature coefficient of about –120 ppm/°C. This slope is
essentially constant to the dielectric constant of silicon and can
be closely compensated by adding a correction term generated
in the same fashion as the proportional-to-temperature (PTAT)
term used to compensate band gap references. The big advantage
of an XFET reference is that the correction term is some 30 times
lower (therefore, requiring less correction) than for a band gap
reference, resulting in much lower noise, because most of the
noise of a band gap reference comes from the temperature
compensation circuitry.
Figure 29 shows the basic topology of the ADR43x series. The
temperature correction term is provided by a current source
with a value designed to be proportional to absolute temperature.
The general equation is
(
PTAT
P
OUT
I
R1
V
Δ
G
V
)
×
×
=
(1)
where:
G
is the gain of the reciprocal of the divider ratio.
V
P
is the difference in pinch-off voltage between the two JFETs.
I
PTAT
is the positive temperature coefficient correction current.
ADR43x devices are created by on-chip adjustment of R2 and
R3 to achieve 2.048 V or 2.500 V, respectively, at the reference
output.
*
I
PTAT
I
1
I
1
*EXTRA CHANNEL IMPLANT
V
OUT
= G(
V
P
– R1
×
I
PTAT
)
R2
V
IN
V
OUT
GND
R3
R1
V
P
0
ADR43x
Figure 29. Simplified Schematic Device
Power Dissipation Considerations
The ADR43x family of references is guaranteed to deliver load
currents to 10 mA with an input voltage that ranges from 4.5 V
to 18 V. When these devices are used in applications at higher
currents, users should use the following equation to account for
the temperature effects due to the power dissipation increases.
A
JA
D
J
T
P
T
+
θ
×
=
(2)
where:
T
J
and
T
A
are the junction and ambient temperatures,
respectively.
P
D
is the device power dissipation.
θ
JA
is the device package thermal resistance.
BASIC VOLTAGE REFERENCE CONNECTIONS
Voltage references, in general, require a bypass capacitor
connected from V
OUT
to GND. The circuit in Figure 30
illustrates the basic configuration for the ADR43x family of
references. Other than a 0.1 μF capacitor at the output to help
improve noise suppression, a large output capacitor at the
output is not required for circuit stability.
+
NIC = NO INTERNAL CONNECTION
TP = TEST PIN (DO NOT CONNECT)
1
2
3
4
5
8
6
7
ADR43x
TOP VIEW
(Not to Scale)
TP
NIC
OUTPUT
TRIM
TP
NIC
V
IN
10
μ
F
0.1
μ
F
0.1
μ
F
0
Figure 30. Basic Voltage Reference Configuration
NOISE PERFORMANCE
The noise generated by the ADR43x family of references is
typically less than 3.75 μV p-p over the 0.1 Hz to 10.0 Hz band
for ADR430, ADR431, and ADR433. Figure 22 shows the 0.1
Hz to 10 Hz noise of the ADR431, which is only 3.5 μV p-p. The
noise measurement is made with a band-pass filter made of a
2-pole high-pass filter with a corner frequency at 0.1 Hz and a
2-pole low-pass filter with a corner frequency at 10.0 Hz.
TURN-ON TIME
Upon application of power (cold start), the time required for
the output voltage to reach its final value within a specified
error band is defined as the turn-on settling time. Two compo-
nents normally associated with this are the time for the active
circuits to settle and the time for the thermal gradients on the
chip to stabilize. Figure 17 and Figure 18 show the turn-on
settling time for the ADR431.
相關PDF資料
PDF描述
ADR433AR-REEL7 Ultralow Noise XFET Voltage References with Current Sink and Source Capability
ADR433ARM Ultralow Noise XFET Voltage References with Current Sink and Source Capability
ADR433ARM-REEL7 Ultralow Noise XFET Voltage References with Current Sink and Source Capability
ADR433B Ultralow Noise XFET Voltage References with Current Sink and Source Capability
ADR433BR Ultralow Noise XFET Voltage References with Current Sink and Source Capability
相關代理商/技術參數
參數描述
ADR433AR 制造商:Analog Devices 功能描述:V-Ref Precision 3V 30mA 8-Pin SOIC N Tube 制造商:Rochester Electronics LLC 功能描述:3.0 V REFERENCE - Bulk
ADR433ARM 制造商:Analog Devices 功能描述:V-Ref Precision 3V 30mA 8-Pin MSOP Tube 制造商:Rochester Electronics LLC 功能描述:3.0 V REFERENCE - Bulk
ADR433ARM-REEL7 制造商:Analog Devices 功能描述:V-Ref Precision 3V 30mA 8-Pin MSOP T/R
ADR433ARMZ 功能描述:IC VREF SERIES PREC 3V 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:XFET® 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:3V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:82µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-TSSOP（5 引線），SC-88A，SOT-353 供應商設備封裝:SC-70-5 包裝:帶卷 (TR) 其它名稱:296-20888-2
ADR433ARMZ-REEL7 功能描述:IC VREF SERIES PREC 3V 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:XFET® 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*