- 您現在的位置：買賣IC網 > PDF目錄375262 > ADP667AR (ANALOG DEVICES INC) +5 V Fixed, Adjustable Low-Dropout Linear Voltage Regulator PDF資料下載
參數資料
| 型號： | ADP667AR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | +5 V Fixed, Adjustable Low-Dropout Linear Voltage Regulator |
| 中文描述： | FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.35 V DROPOUT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 135K |
| 代理商： | ADP667AR |
ADP667
REV. 0
–5–
Dropout Detector
The ADP667 features an extremely low dropout voltage making
it suitable for low voltage systems where headroom is limited. A
dropout detector is also provided. The dropout detector output,
DD, changes as the dropout voltage approaches its limit. This is
useful for warning that regulation can no longer be maintained.
The dropout detector output is an open collector output from a
PNP transistor. Under normal operating conditions with the in-
put voltage more than 300 mV above the output, the PNP tran-
sistor is off and no current flows out the DD pin. As the voltage
differential reduces to less than 300 mV, the transistor switches
on and current is sourced. This condition indicates that regulation
can no longer be maintained. Please refer to Figure 10 in the
“Typical Performance Characteristics.” The current output can
be translated into a voltage output by connecting a resistor from
DD to GND. A resistor value of 100 k
is suitable. A digital
status signal can be obtained using a comparator. The on-chip
comparator LBI may be used if it is not being used to monitor a
battery voltage. This is illustrated in Figure 5.
+
C1
10μF
IN
OUT
LBO
ADP667
+5V
OUTPUT
R2
10k
LBI
GND
SET
SHDN
DROPOUT
STATUS
OUTPUT
DD
V
IN
R1
100k
+
Figure 5. Dropout Status Output
Output Capacitor Selection
An output capacitor is required on the ADP667 to maintain
stability and also to improve the load transient response. Ca-
pacitor values from 10
μ
F upwards are suitable. All specifica-
tions are tested and guaranteed with 10
μ
F. Capacitors larger
than 10
μ
F will further improve the dynamic transient response
characteristics of the regulator. Tantalum or aluminum electro-
lytics are suitable for most applications. For temperatures below
about –25
°
C, solid tantalums should be used as many alumi-
num electrolytes freeze at this temperature.
Quiescent Current Considerations
The ADP667 uses a PNP output stage to achieve low dropout
voltages combined with high output current capability. Under
normal regulating conditions the quiescent current is extremely
low. However if the input voltage drops so that it is below the
desired output voltage, the quiescent current increases consider-
ably. This happens because regulation can no longer be main-
tained and large base current flows in the PNP output transistor
in an attempt to hold it fully on. For minimum quiescent cur-
rent, it is therefore important that the input voltage is main-
tained higher than the desired output level. If the device is being
powered using a battery that can discharge down below the rec-
ommended level, there are a couple of techniques that can be
applied to reduce the quiescent current, but at the expense of
dropout voltage. The first of these is illustrated in Figure 6. By
connecting DD to SHDN the regulator is partially disabled with
input voltages below the desired output voltage and therefore
the quiescent current is reduced considerably.
+
C1
10μF
IN
OUT
ADP667
+5V
OUTPUT
GND
SET
SHDN
DD
V
IN
R1
47k
+
C2
0.1μF
Figure 6. IQ Reduction 1
Another technique for reducing the quiescent current near drop-
out is illustrated in Figure 7. The DD output is used to modify
the output voltage so that as V
IN
drops, the desired output volt-
age setpoint also drops. This technique only works when exter-
nal resistors are used to set the output voltage. With V
IN
greater
than V
OUT
, DD has no effect. As V
IN
reduces and dropout is
reached, the DD output starts sourcing current into the SET
input through R3. This increases the SET voltage so that the
regulator feedback loop does not drive the internal PNP transis-
tor as hard as it otherwise would. As the input voltage continues
to decrease, more current is sourced, thereby reducing the PNP
drive even further. The advantage of this scheme is that it main-
tains a low quiescent current down to very low values of V
IN
at
which point the batteries are well outside their useful operating
range. The output voltage tracks the input voltage minus the
dropout. The SHDN function is also unaffected and may be
used normally if desired.
+
C1
10μF
IN
OUT
ADP667
+5V
OUTPUT
GND
SET
SHDN
DD
R1
332k
R2
1M
R3
1M
+
V
IN
Figure 7. IQ Reduction 2
相關PDF資料 |
PDF描述 |
|---|---|
| ADR121 | Precision, Micropower LDO Voltage References in TSOT |
| ADR121AUJZ-R2 | Precision, Micropower LDO Voltage References in TSOT |
| ADR121AUJZ-REEL7 | Precision, Micropower LDO Voltage References in TSOT |
| ADR121BUJZ-REEL7 | Precision, Micropower LDO Voltage References in TSOT |
| ADR125 | Precision, Micropower LDO Voltage References in TSOT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP667AR-REEL | 制造商:Analog Devices 功能描述:LDO Regulator Pos 1.3V to 16V5V 0.25A 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:LOW DROPOUT LINEAR VOLTAGE REGULATOR - Tape and Reel |
| ADP667AR-REEL7 | 制造商:Analog Devices 功能描述:LDO Regulator Pos 1.3V to 16V5V 0.25A 8-Pin SOIC N T/R 制造商:Rochester Electronics LLC 功能描述:LOW DROPOUT LINEAR VOLTAGE REGULATOR - Tape and Reel |
| ADP667ARZ | 功能描述:IC REG LDO 5V/ADJ .25A 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| ADP667ARZ-AIRBUS | 制造商:Analog Devices 功能描述: |
| ADP667ARZ-REEL | 制造商:Analog Devices 功能描述:LDO Regulator Pos 1.3V to 16V5V 0.25A 8-Pin SOIC N T/R |
發布緊急采購，3分鐘左右您將得到回復。