- 您現在的位置：買賣IC網 > PDF目錄374023 > ADP3820ART-42 (Analog Devices, Inc.) Circular Connector; No. of Contacts:17; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Cable Receptacle; Insert Arrangement:20-29 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | ADP3820ART-42 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:17; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Cable Receptacle; Insert Arrangement:20-29 RoHS Compliant: No |
| 中文描述： | 鋰離子電池充電器 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 112K |
| 代理商： | ADP3820ART-42 |
ADP3820
–6–
REV. A
APPLICATION INFORMATION
The ADP3820 is very easy to use. A P-channel power MOS-
FET and a small capacitor on the output is all that is needed to
form an inexpensive Li-Ion battery charger. The advantage of
using the ADP3820 controller is that it can directly drive a
PMOS FET to provide a regulated output current until the
battery is charged. When the specified battery voltage is reached,
the charge current is reduced and the ADP3820 maintains the
maximum specified battery voltage accurately.
When fully charged, the circuit in Figure 1 works like a well
known linear regulator, holding the output voltage within the
specified accuracy as needed by single cell Li-Ion batteries. The
output is sensed by the V
OUT
pin. When charging a discharged
battery, the circuit maintains a set charging current determined
by the current sense resistor until the battery is fully charged,
then reduces it to a trickle charge to keep the battery at the
specified voltage. The voltage drop across the R
S
current sense
resistor is sensed by the IS input of the ADP3820. At minimum
battery voltage or at shorted battery, the circuit reduces this
current (foldback) to limit the dissipation of the FET (see Fig-
ure 13). Both the V
IN
input and V
OUT
sense pins of the IC need
to be bypassed by a suitable bypass capacitor.
A 6 V gate-to-source voltage clamp is provided by the ADP3820
to protect the MOSFET gates at higher source voltages. The
ADP3820 also has a TTL
SD
input, which may be connected to
the input voltage to enable the IC. Pulling it to low or to
ground will disable the FET-drive.
Design Approach
Due to the lower efficiency of Linear Regulator Charging, the
most important factor is the thermal design and cost, which is
the direct function of the input voltage, output current and
thermal impedance between the MOSFET and the ambient
cooling air. The worse-case situation is when the battery is
shorted since the MOSFET has to dissipate the maximum power.
A tradeoff must be made between the charge current, cost and
thermal requirements of the charger. Higher current requires a
larger FET with more effective heat dissipation leading to a
more expensive design. Lowering the charge current reduces
cost by lowering the size of the FET, possibly allowing a smaller
package such as SOT-23-6. The following designs consider both
options.
Furthermore, each design is evaluated under two input
source voltage conditions.
Regarding input voltage, there are two options:
A. The input voltage is preregulated, e.g., 5 V
±
10%
B. The input voltage is not a preregulated source, e.g., a wall
plug-in transformer with a rectifier and capacitive filter.
Higher Current Option
A. Preregulated Input Voltage (5 V
6
10%)
For the circuit shown in Figure 1, the required
θ
JA
thermal
impedance can be calculated as follows: if the FET data sheet
allows a max FET junction temperature of T
JMAX
= 150
°
C
,
then
at 50
°
C ambient and at convection cooling, the maximum al-
lowed
T junction temperature rise is thus, T
JMAX
– T
AMAX
=
150
°
C – 50
°
C = 100
°
C.
The maximum current for a shorted or discharged battery is
reduced from the set charge current by a multiplier factor shown
in Figure 13 due to the foldback current limiting feature of the
ADP3820. This k factor between V
O
of 0 V to about 2.5 V is:
k ~ 0.65.
θ
J
A
=
T/
(
I
O
×
k
×
V
IN
)
=
100
/
(1
×
0.65
×
5)
=
30.7
°
C/W
This thermal impedance can be realized using the transistor
shown in Figure 1 when surface mounted to a 40
×
40 mm
double-sided PCB with many vias around the tab of the surface-
mounted FET to the backplane of the PCB. Alternatively, a
TO-220 packaged FET mounted to a heatsink could be used.
The
θ
or thermal impedance of a suitable heatsink is calculated
below:
θ
<
(
θ
JA
–
θ
JC
)
=
30.7
– 2 = +28.7
°
C/W
Where the
θ
JC
, or junction-to-case thermal impedance of the
FET can be read from the FET data sheet. A low cost such
heatsink is type PF430 made by Thermalloy, with a
θ
=
+25.3
°
C/W.
The current sense resistor for this application can be simply
calculated:
R
S
=
V
S
/
I
O
= 0.05/1 = 50
m
Where
V
S
is specified on the data sheet as current limit threshold
voltage at 40 mV–75 mV. For battery charging applications, it
is adequate to use the typical 50 mV midvalue.
B. Nonpreregulated Input Voltage
If the input voltage source is, for example, a rectified and
capacitor-filtered secondary voltage of a small wall plug-in
transformer, the heatsinking requirement is more demanding.
The V
INMIN
should be specified 5 V, but at the lowest line volt-
age and full load current. The required thermal impedance can
be calculated the same way as above, but here we have to use
the maximum output rectified voltage, which can be substan-
tially higher than 5 V, depending on transformer regulation and
line voltage variation. For example, if V
INMAX
is 10 V
θ
JA
=
T/
(
I
O
×
k
×
V
INMAX
)
=
100
/
(1
×
0.65
×
10)
=
+15.3
°
C/W
The
θ
suitable heatsink thermal impedance:
θ
<
θ
JA
–
θ
JC
=
15.3
–
2
=
13.3
°
C/W
A low cost heatsink is Type 6030B made by Thermalloy, with a
θ
=
+12.5
°
C/W.
Lower Current Option
A. Preregulated Input Voltage (5 V
6
10%)
If lower charging current is allowed, the
θ
JA
value can be increased,
and the system cost decreased. The lower cost is assured by
using an inexpensive MOSFET with, for example, a NDT452P
in a SOT-23-6 package mounted on a small 40
×
40 mm area
on double-sided PCB. This provides a convection cooled ther-
mal impedance of
θ
JA
=
+55
°
C/W, presuming many vias are
used around the FET to the backplane. Allowing a maximum
FET junction temperature of +150
°
C, at +50
°
C ambient, and
at convection cooling the maximum allowed heat rise is thus
150
°
C–50
°
C = 100
°
C.
The maximum foldback current allowed:
I
FB
=
T/
(
θ
×
V
IN
)
=
100
/
(55
×
5)
=
0.33
A
Thus the full charging current:
I
OUTMAX
=
I
FB
/
k
= 0.5
A
k
is calculated in the above example.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3820 | Li-Ion Battery Chargers(鋰離子電池充電器) |
| ADR02AKS-R2 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
| ADR01 | Ultracompact Precision10 V/5 V/2.5 V/3.0 V Voltage References |
| ADR01AKS-R2 | Ultracompact Precision10 V/5 V/2.5 V/3.0 V Voltage References |
| ADR01AKS-REEL7 | Ultracompact Precision10 V/5 V/2.5 V/3.0 V Voltage References |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3820ARTZ-4.1RL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADP3820ARTZ-4.2RL7 | 功能描述:IC CHARGER LI-ION 4.2V SOT-23-6 RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ADP4000 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Programmable Multi-Phase Synchronous Buck Converter with PMBus |
| ADP4000JCPZ-REEL | 功能描述:肖特基二極管與整流器 VR11.1 6PH CTRL W/PMBUS ITF RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| ADP4000JCPZ-RL7 | 功能描述:MOSFET VR11.1 6PH CTRL W/PMBUS ITF RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。