- 您現在的位置：買賣IC網 > PDF目錄374023 > ADP3820AR-41 (Analog Devices, Inc.) Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | ADP3820AR-41 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| 中文描述： | 鋰離子電池充電器 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 112K |
| 代理商： | ADP3820AR-41 |
ADP3820
–7–
REV. A
The current sense resistor for this application:
R
S
=
V
S
/I
O
= 0.05/0.5 = 100
m
FET Selection
The type and size of the pass transistor are determined by the
threshold voltage, input-output voltage differential and load
current. The selected PMOS must satisfy the physical and ther-
mal design requirements. To ensure that the maximum V
GS
provided by the controller will turn on the FET at worst case
conditions, (i.e., temperature and manufacturing tolerances) the
maximum available V
GS
must be determined. Maximum V
GS
is
calculated as follows:
V
GS
=
V
IN
–
V
BE
–
I
OUTMAX
×
R
S
where
I
OUTMAX
= Maximum Output Current
R
S
= Current Sense Resistor
V
BE
~ 0.7 V (Room Temperature)
~ 0.5 V (Hot)
~ 0.9 V (Cold)
For example:
V
IN
= 5
V,
and
I
OUTMAX
= 1
A,
V
GS
= 5
V
– 0.7
V –
1
A
×
50
m
=
4.25
V
If
V
GS
< 5 V, logic level FET should be considered.
If
V
GS
> 5 V, either logic level or standard MOSFET can be
used.
The difference between V
IN
and V
O
(V
DS
) must exceed the
voltage drop due to the sense resistor plus the ON-resistance
of the FET at the maximum charge current. The selected
MOSFET must satisfy these criteria; otherwise, a different pass
device should be used.
V
DS
=
V
IN
–
V
O
=
5
V –
4.2
V =
0.8
V
The maximum R
DS(ON)
required at the available gate drive (V
DR
)
and Drain-to-Source voltage (V
DS
) is:
R
DS
(
ON
)
=
V
DS
/
I
OUTMAX
From the Drain-to Source current vs. Drain-to-Source voltage
vs. gate drive graph off the MOSFET data sheet, it can be de-
termined if the above calculated R
DS(ON)
is higher than the graph
indicates. However, the value read from the MOSFET data
sheet graph must be adjusted based on the junction temperature
of the MOSFET. This adjustment factor can be obtained from
the normalized R
DS(ON)
vs. junction temperature graph in the
MOSFET data sheet.
External Capacitors
The ADP3820 is stable with or without a battery load, and
virtually any good quality output filter capacitors can be used
(anyCAP), independent of the capacitor’s minimum ESR
(Effective Series Resistance) value. The actual value of the
capacitor and its associated ESR depends on the g
m
and capaci-
tance of the external PMOS device. A 10
μ
F tantalum or alumi-
num electrolytic capacitor at the output is sufficient to ensure
stability for up to a 10 A output current.
Shutdown Mode
Applying a TTL high signal to the
SD
pin or tying it to the
input pin will enable the output. Pulling this pin low or tying
it to ground will disable the output. In shutdown mode, the
controller’s quiescent current is reduced to less than 1
μ
A.
Gate-to-Source Clamp
A 6 V gate-to-source voltage clamp is provided by the ADP3820 to
protect most MOSFET gates in the event the V
IN
> V
GS
allowed
and the output is suddenly shorted to ground. This allows use of
the new, low R
DS(ON)
MOSFETs.
Short Circuit Protection
The power FET is protected during short circuit conditions
with a foldback type of current limiting that significantly re-
duces the current. See Figure 13 for foldback current limit
information.
Current Sense Resistor
Current limit is achieved by setting an appropriate current sense
resistor (R
S
) across the current limit threshold voltage. Current
limit sense resistor, R
S
, is calculated as shown above. Proper
derating is advised to select the power dissipation rating of the
resistor.
The simplest and cheapest sense resistor for high current appli-
cations, (i.e., Figure 1) is a PCB trace. However, the tempera-
ture dependence of the copper trace and the thickness tolerances of
the trace must be considered in the design. The resistivity of
copper has a positive temperature coefficient of +0.39%/
°
C.
Copper’s Tempco, in conjunction with the proportional-to-
absolute temperature (
±
0.3%) current limit voltage, can provide
an accurate current limit. Table I provides the typical resistance
values for PCB copper traces. Alternately, an appropriate sense
resistor, such as surface mount sense resistors, available from
KRL, can be used.
Table I. Printed Circuit Copper Resistance
Conductor
Thickness
1/2oz/ft
2
(18
μ
m)
Conductor
Width/Inch
Resistance
m
V
/In
0.025
0.050
0.100
0.200
0.500
39.3
19.7
9.83
4.91
1.97
1oz/ft
2
(35
μ
m)
0.025
0.050
0.100
0.200
0.500
19.7
9.83
4.91
2.46
0.98
2oz/ft
2
(70
μ
m)
0.025
0.050
0.100
0.200
0.500
9.83
4.91
2.46
1.23
0.49
3oz/ft
2
(106
μ
m)
0.025
0.050
0.100
0.200
0.500
6.5
3.25
1.63
0.81
0.325
anyCAP is a trademark of Analog Devices, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| ADP3820AR-42 | Circular Connector Cable Assembly; Connector Type A:Circular Receptacle; Connector Type B:Stripped End Leads; Cable Length:10ft RoHS Compliant: Yes |
| ADP3820ART-41 | Lithium-Ion Battery Charger |
| ADP3820ART-42 | Circular Connector; No. of Contacts:17; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:20; Circular Contact Gender:Socket; Circular Shell Style:Cable Receptacle; Insert Arrangement:20-29 RoHS Compliant: No |
| ADP3820 | Li-Ion Battery Chargers(鋰離子電池充電器) |
| ADR02AKS-R2 | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADP3820AR-42 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Lithium-Ion Battery Charger |
| ADP3820ART-4.1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Battery Management |
| ADP3820ART-4.1RL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ADP3820ART-4.1-RL | 制造商:Analog Devices 功能描述:Battery Charger Li-Ion 1mA 4.1V 6-Pin SOT-23 T/R |
| ADP3820ART-4.1-RL7 | 制造商:Analog Devices 功能描述:Battery Charger Li-Ion 1mA 4.1V 6-Pin SOT-23 T/R 制造商:Rochester Electronics LLC 功能描述:LITHIUM ION BATTERY CHARGER CONTROLLER - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。