- 您現在的位置：買賣IC網 > PDF目錄374010 > ADM691 (Analog Devices, Inc.) Microprocessor Supervisory Circuits PDF資料下載
參數資料
| 型號： | ADM691 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Microprocessor Supervisory Circuits |
| 中文描述： | 微處理器監控電路 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 337K |
| 代理商： | ADM691 |
ADM691A/ADM693A/ADM800L/M
–7–
REV. 0
10
0%
100
90
400ms
1V
Figure 14.
RESET
Output Voltage vs. Supply
10
0%
100
90
10μs
1V
Figure 15.
RESET
Response Time
POWER FAIL
RESET
OUTPUT
RESET
is an active low output that provides a reset signal to the
Microprocessor whenever V
CC
is at an invalid level. When V
CC
falls below the reset threshold, the
RESET
output is forced
low. The reset voltage threshold is 4.65 V (ADM691A/
ADM800L) or 4.4 V (ADM693A/ADM800M).
On power-up
RESET
will remain low for 200 milliseconds after
V
CC
rises above the appropriate reset threshold. This allows time
for the power supply and microprocessor to stabilize. On power-
down, the
RESET
output remains low with V
CC
as low as 1 V.
This ensures that the microprocessor is held in a stable shut-
down condition. If
RESET
is required to be low for voltages be-
low 1 V, this may be achieved by connecting a pull-down resistor
on the
RESET
line. The resistor will help maintain
RESET
low
down to V
CC
= 0 V. Note that this is only necessary if V
BATT
is
below 2 V. With battery voltages
≥
2 V
RESET
will function cor-
rectly with V
CC
from 0 V to +5.5 V.
This reset active time is adjustable by using an external oscillator
or by connecting an external capacitor to the OSC IN pin. Refer
to Table II.
The guaranteed minimum and maximum thresholds of the
ADM691A/ADM800L are 4.5 V and 4.75 V, while the guaran-
teed thresholds of the ADM693A/ADM800M are 4.25 V and
4.5 V. The ADM691A/ADM800L is therefore compatible with
5 V supplies with a +10%, –5% tolerance while the ADM693A/
ADM800M is compatible with 5 V
±
10% supplies.
In addition to
RESET
an active high RESET output is provided.
This is the complement of
RESET
and is useful for processors
requiring an active high RESET signal.
Watchdog Timer Reset
The watchdog timer circuit monitors the activity of the micro-
processor in order to check that it is not stalled in an indefinite
loop. An output line on the processor is used to toggle the
Watchdog Input (WDI) line. If this line is not toggled within the
selected timeout period, a reset pulse is generated. The watch-
dog timeout period may be configured for either a fixed “short”
100 ms or a “l(fā)ong” 1.6 second timeout period or for an adjust-
able timeout period. Note that even if the short timeout period
is selected, the first time out immediately following a reset is
1.6 sec. This is to allow additional time for the microprocessor
to regain control following a reset.
The watchdog timer is restarted at the end of reset, whether the
reset was caused by lack of activity on WDI or by V
CC
falling be-
low the reset threshold.
The normal (short) timeout period becomes effective following
the first transition of WDI after reset has gone inactive. The
watchdog timeout period restarts with each transition on the
WDI pin. To ensure that the watchdog timer does not time out,
either a high-to-low or low-to high transition on the WDI pin
must occur at or less than the minimum timeout period. If WDI
remains permanently either high or low, reset pulses will be is-
sued after each timeout period (1.6 seconds). The watchdog
monitor can be deactivated by floating the Watchdog Input
(WDI). If floating, an internal resistor network biases WDI to
around 1.6 V.
COUTPUT
CONTROL
V
BATT
V
CC
CE
IN
OSC IN
OSC SEL
WATCHDOG
INPUT (WDI)
POWER FAIL
INPUT (PFI)
1
VOLTAGE DETECTOR = 4.4V (ADM693A/ADM800M)
ADM691A/ADM693A
ADM800L/ADM800M
1.25V
WATCHDOG
TRANSITION DETECTOR
WATCHDOG
TIMER
TIMEBASE
GRESET &
4.65V
1
BATT ON
LOW LINE
V
OUT
CE
OUT
RESET
RESET
WATCHDOG
OUTPUT (
WDO
)
POWER FAIL
OUTPUT (
PFO
)
Figure 16. Functional Block Diagram
Watchdog Output (
WDO
)
The Watchdog Output
WDO
provides a status output that goes
low if the watchdog timer “times out” and remains low until set
high by the next transition on the watchdog input.
WDO
is also
set high when V
CC
goes below the reset threshold. If WDI re-
mains high or low indefinitely,
RESET
and RESET will gener-
ate 200 ms pulses every 1.6 sec.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM691AN | Analog Switch / Multiplexer (Mux) IC; Analog Switch Function:Switch; Package/Case:6-SC-89; Leaded Process Compatible:Yes; Leakage Current:1nA; On Resistance, Rds(on):2ohm; Peak Reflow Compatible (260 C):Yes; Reel Quantity:3000 RoHS Compliant: Yes |
| ADM691AR | Microprocessor Supervisory Circuits |
| ADM691SQ | Microprocessor Supervisory Circuits |
| ADM693A | Microprocessor Supervisory Circuits |
| ADM693AAN | Microprocessor Supervisory Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM6918ABT1 | 功能描述:IC SWITCH CNTRLR 10/100 128FQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ADM6918XABT1 | 功能描述:IC SWITCH CNTRLR 10/100 128FQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ADM691A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Microprocessor Supervisory Circuits |
| ADM691AAN | 功能描述:IC SUPER MPU 4.65 250MA 16DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM691AANZ | 功能描述:IC SUPERVISOR MPU 4.65V 16DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 其它有關文件:STM6905 View All Specifications 標準包裝:1 系列:- 類型:多壓監控器 監視電壓數目:5 輸出:開路漏極或開路集電極 復位:低有效 復位超時:最小為 140 ms 電壓 - 閥值:2.188V，2.955V，可調，可調，可調 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-TSSOP 包裝:Digi-Reel® 產品目錄頁面:1197 (CN2011-ZH PDF) 其它名稱:497-8728-6 |
發布緊急采購，3分鐘左右您將得到回復。