- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM483EAR (ANALOG DEVICES INC) +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver PDF資料下載
參數資料
| 型號： | ADM483EAR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 324K |
| 代理商： | ADM483EAR |
ADM483E
–7–
REV. 0
I-O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I-O cable can result in a static
discharge that can damage or completely destroy the interface
product connected to the I-O port.
It is, therefore, extremely important to have high levels of ESD
protection on the I-O lines.
It is possible that the ESD discharge could induce latchup in the
device under test. It is therefore important that ESD testing on
the I-O pins be carried out while device power is applied. This
type of testing is more representative of a real world I-O
discharge where the equipment is operating normally when the
discharge occurs.
100%
90%
36.8%
10%
I
P
t
RL
t
DL
TIME t
Figure 22. Human Body Model ESD Current Waveform
Table IV. ADM483E ESD Test Results
ESD Test Method
I-O Pins
Other Pins
Human Body Model: Air
Human Body Model: Contact
±
15 kV
±
8 kV
±
3.5 V
FAST TRANSIENT BURST IMMUNITY (IEC1000-4-4)
IEC1000-4-4 (previously 801-4) covers electrical fast-transient/
burst (EFT) immunity. Electrical fast transients occur as a
result of arcing contacts in switches and relays. The tests
simulate the interference generated when, for example, a power
relay disconnects an inductive load. A spark is generated due to
the well known back EMF effect. In fact, the spark consists of a
burst of sparks as the relay contacts separate. The voltage
appearing on the line, therefore, consists of a burst of extremely
fast transient impulses. A similar effect occurs when switching
on fluorescent lights.
The fast transient burst test, defined in IEC1000-4-4, simulates
this arcing and its waveform is illustrated in Figure 23. It
consists of a burst of 2.5 kHz to 5 kHz transients repeating at
300 ms intervals. It is specified for both power and data lines.
Four severity levels are defined in terms of an open-circuit
voltage as a function of installation environment. The installa-
tion environments are defined as
1. Well-protected
2. Protected
3. Typical Industrial
4. Severe Industrial
300ms
16ms
V
t
V
0.2/0.4ms
t
5ns
50ns
Figure 23. IEC1000-4-4 Fast Transient Waveform
Table V shows the peak voltages for each of the environments.
Table V.
Level
V
PEAK
(kV)
PSU
V
PEAK
(kV)
I-O
1
2
3
4
0.5
1
2
4
0.25
0.5
1
2
A simplified circuit diagram of the actual EFT generator is
illustrated in Figure 24.
These transients are coupled onto the signal lines using an EFT
coupling clamp. The clamp is 1 m long and completely sur-
rounds the cable, providing maximum coupling capacitance
(50 pF to 200 pF typ) between the clamp and the cable. High
energy transients are capacitively coupled onto the signal lines.
Fast rise times (5 ns) as specified by the standard result in very
effective coupling. This test is very severe since high voltages are
coupled onto the signal lines. The repetitive transients can often
cause problems, where single pulses do not. Destructive latchup
may be induced due to the high energy content of the transients.
Note that this stress is applied while the interface products are
powered up and are transmitting data. The EFT test applies
hundreds of pulses with higher energy than ESD. Worst case
transient current on an I-O line can be as high as 40 A.
HIGH
VOLTAGE
SOURCE
R
C
R
M
C
C
Z
S
L
C
D
50
OUTPUT
Figure 24. EFT Generator
Test results are classified according to the following
1. Normal performance within specification limits.
2. Temporary degradation or loss of performance that is self-
recoverable.
3. Temporary degradation or loss of function or performance
that requires operator intervention or system reset.
4. Degradation or loss of function that is not recoverable due to
damage.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM483E | +-15 kV ESD Protected, EMC Compliant Slew Rate Limited, EIA RS-485 Transceiver |
| ADM483 | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
| ADM483AR-REEL7 | 5 V Low Power, Slew-Rate Limited RS-485/RS-422 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM483EAR-1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM483EAR-1REEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADM483EAR-REEL | 功能描述:IC TX/RX RS-485 LO-SLEW 5V 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM483EARZ | 功能描述:IC TX/RX RS-485 LO-SLEW 5V 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| ADM483EARZ | 制造商:Analog Devices 功能描述:Transceiver IC 制造商:Analog Devices 功能描述:IC, RS485 TRANSCEIVER 250KBPS 5.5V SOIC8 |
發布緊急采購，3分鐘左右您將得到回復。