- 您現在的位置：買賣IC網 > PDF目錄374003 > ADM3311EARU-Reel25 (Analog Devices, Inc.) 15 kV ESD Protected, +2.7 V to +3.6 V Serial Port Transceiver with Green Idle⑩ PDF資料下載
參數資料
| 型號： | ADM3311EARU-Reel25 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 15 kV ESD Protected, +2.7 V to +3.6 V Serial Port Transceiver with Green Idle⑩ |
| 中文描述： | 15 kV的ESD保護，2.7 V到3.6 V綠色串口收發閑置⑩ |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 180K |
| 代理商： | ADM3311EARU-REEL25 |
ADM3311E
–9–
REV. A
D1
D2
Tx
TRANSMITTER
OUTPUT
Figure 21b. Transmitter Output Protection Scheme
ESD TESTING (IEC1000-4-2)
IEC1000-4-2 (previously 801-2) specifies compliance testing
using two coupling methods, contact discharge and air-gap
discharge. Contact discharge calls for a direct connection to the
unit being tested. Air-gap discharge uses a higher test voltage
but does not make direct contact with the unit under test. With
air discharge, the discharge gun is moved toward the unit under
test, developing an arc across the air gap, hence the term air
discharge. This method is influenced by humidity, temperature,
barometric pressure, distance and rate of closure of the discharge
gun. The contact-discharge method, while less realistic, is more
repeatable and is gaining acceptance in preference to the air-gap
method.
Although very little energy is contained within an ESD pulse,
the extremely fast rise time coupled with high voltages can cause
failures in unprotected semiconductors. Catastrophic destruc-
tion can occur immediately as a result of arcing or heating. Even
if catastrophic failure does not occur immediately, the device
may suffer from parametric degradation, which may result in
degraded performance. The cumulative effects of continuous
exposure can eventually lead to complete failure.
I-O lines are particularly vulnerable to ESD damage. Simply
touching or plugging in an I-O cable can result in a static dis-
charge that can damage or completely destroy the interface
product connected to the I-O port. Traditional ESD test meth-
ods such as the MIL-STD-883B method 3015.7 do not fully
test a product’s susceptibility to this type of discharge. This test
was intended to test a product’s susceptibility to ESD damage
during handling. Each pin is tested with respect to all other
pins. There are some important differences between the tradi-
tional test and the IEC test:
(a) The IEC test is much more stringent in terms of discharge
energy. The peak current injected is over four times greater.
(b) The current rise time is significantly faster in the IEC test.
(c) The IEC test is carried out while power is applied to the device.
It is possible that the ESD discharge could induce latch-up in the
device under test. This test is therefore more representative of a
real-world I-O discharge where the equipment is operating nor-
mally with power applied. For maximum peace of mind however,
both tests should be performed, thus ensuring maximum protec-
tion both during handling and later, during field service.
R1
R2
C1
DEVICE
UNDER TEST
HIGH
VOLTAGE
GENERATOR
ESD TEST METHOD
H. BODY MIL-STD883B
IEC1000-4-2
R2
1.5k
330
C1
100pF
150pF
Figure 22. ESD Test Standards
100
I
P
–
90
36.8
10.0
TIME t
t
DL
t
RL
Figure 23. Human Body Model ESD Current Waveform
100
I
P
–
90
10
TIME t
30ns
60ns
0.1 TO 1ns
Figure 24. IEC1000-4-2 ESD Current Waveform
The ADM3311E is tested using both of the above-mentioned
test methods. All pins are tested with respect to all other pins as
per the MIL-STD-883B specification. In addition, all I-O pins
are tested as per the IEC test specification. The products were
tested under the following conditions:
(a) Power-On—Normal Operation
(b) Power-Off
Four levels of compliance are defined by IEC1000-4-2. The
ADM3311E meets the most stringent compliance level for con-
tact discharge. This means that the products are able to with-
stand contact discharges in excess of 8 kV.
Table II. IEC1000-4-2 Compliance Levels
Contact Discharge
(kV)
2
4
6
8
Air Discharge
(kV)
2
4
8
15
Level
1
2
3
4
Table III. ADM3311E ESD Test Results
ESD Test Method
I-O Pins (kV)
±
15
Other Pins (kV)
±
3
MIL-STD-883B
IEC1000-4-2
Contact
±
8
相關PDF資料 |
PDF描述 |
|---|---|
| ADM3311 | JFET; Breakdown Voltage, V(br)gss:40V; Zero Gate Voltage Drain Current Min, Idss:-4mA; Zero Gate Voltage Drain Current Max, Idss:-16mA; Gate-Source Cutoff Voltage Max, Vgs(off):9V; Continuous Drain Current, Id:-16mA RoHS Compliant: No |
| ADM3315EACP-REEL | 15 kV ESD Protected, 2.7 V to 3.6 V Serial Port Transceivers with Green Idle⑩ |
| ADM3315EACP-REEL7 | 15 kV ESD Protected, 2.7 V to 3.6 V Serial Port Transceivers with Green Idle⑩ |
| ADM3315EARU | 10-825810-AAP |
| ADM3315EARU-REEL | 15 kV ESD Protected, 2.7 V to 3.6 V Serial Port Transceivers with Green Idle⑩ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM3311EARU-REEL7 | 功能描述:IC TXRX RS-232 3:5 2.7V 28TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM3311EARUZ | 功能描述:IC TX/RX RS-232 2.7/3.6V 28TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM3311EARUZ | 制造商:Analog Devices 功能描述:RS-232 IC |
| ADM3311EARUZ-REEL | 功能描述:IC TXRX RS-232 3:5 2.7V 28TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM3311EARUZ-REEL7 | 功能描述:IC TXRX RS-232 3:5 2.7V 28TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。