- 您現在的位置：買賣IC網 > PDF目錄373998 > ADM1487AR (ANALOG DEVICES INC) Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection PDF資料下載
參數資料
| 型號： | ADM1487AR |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection |
| 中文描述： | LINE TRANSCEIVER, PDSO8 |
| 封裝： | SO-8 |
| 文件頁數： | 7/8頁 |
| 文件大?。?/td> | 387K |
| 代理商： | ADM1487AR |
ADM1487
Rev. PrC
–7–
TRANSMITTING
INPUTS
OUTPUTS
RE
D E
DI
Z
Y
X
1
1
0
1
X
1
0
1
0
0
0
X
High-Z
High-Z
1
0
X
Shutdown*
X = Don’t care
CIRCUIT DESCRIPTION
The ADM1487 is a differential input, differential output
transceiver designed RS-485/RS-422 serial data communi-
cations over twisted-pair cables. It is a half-duplex device
intended for alternate transmission and reception of data
over a single twisted-pair cable, and the driver outputs and
receiver inputs are internally linked and brought out to a
single pair of pins.
Its principal features include ultra-low power operation, a
controlled slew-rate driver that minimizes electromagnetic
interference (EMI) and signals reflections due to incor-
rectly terminated lines, and high input impedance that al-
lows up to 256 receivers to be connected to a bus.
THREE-STATE BUS CONNECTION
The ADM1487 has a Driver Enable pin (DE) that enables
the driver outputs when taken high or puts the driver out-
puts into a high-impedance state when taken low. This al-
lows several driver outputs to be connected to an RS-422/
RS-485 bus.
Similarly, the device has a (active-low) Receiver Enable
pin (
RE
). Taking this low enables the receiver, while tak-
ing it high puts the receiver outputs into a high-impedance
state. This allows several receiver outputs to be connected
to a serial data bus.
The input impedance of the device is 96k , which is 8
times higher than the standard RS-485 load of 12k . A
standard driver can driver 32 standard loads, so up to 256
ADM1487 receivers, or a combination of ADM1487 and
other devices up to 32 unit loads, may be connected to an
RS-422/RS485 bus driven by a single driver.
LOW POWER OPERATION
The ADM1487 draws very little supply current (typically
80μA) when the driver outputs are disabled or unloaded.
This will increase by up to 72μA if the driver outputs are
enabled (but unloaded) and applying the maximum output
swing of 5V across the receiver input resistors.
However, in practical applications with the device driving
and RS-485/RS422 cable or bus, the current drain is
dominated by the current sourced into the line termination
resistors and any other devices on the bus. With a half-ter-
mination (120 load) between the driver outputs, the load
current can be in excess of 13mA as the drivers force a
minimum of 1.5V across the line, and can be greater than
25mA with a fully terminated 60 line attached.
DEVICE TRUTH TABLES
SHUTDOWN MODE
If
RE
is taken high while DE is taken low, the device will
enter a low-power shutdown mode, in which the supply
current is typically 1μA.
If the driver outputs are active immediately before shut-
down (DE high), the supply current will not drop to 1μ
until the driver outputs have settled to their three-state
mode, which can take up to 2.6μs worst-case. If DE is al-
ready low and shutdown is entered by taking
RE
high, the
supply current will drop to 1μA very quickly.
When
RE
is taken low and/or DE is takem high, the de-
vice will wake up within 3.5μs.
If shutdown mode is not used, the fact that DE is active-
high and
RE
is active-low offers a convenient way of
switching the device between transmit and receive, by ty-
ing DE and
RE
together. This is useful, for example, in
applications using half duplex operation and where several
receiver outputs are connected to a serial bus.
The device is guaranteed not to enter shutdown mode if
DE and
RE
are driven in this way. If DE is low and
RE
is
high for less than 50ns the device will not enter shutdown.
If DE is low and
RE
is high for greater than 600ns, the
device is guaranteed to enter shutdown.
RECEIVER INPUTS
The ADM1487 receiver has an input common-mode
range covering the entire RS-485 range of –7V to 12V.
Internal 96k
input resistors from each line terminal to
ground provide a 1/8 unit load to the RS485 bus.
Differential signals greater than ±200mV within the speci-
fied input common-mode range are converted to a TTL-
compatible logic signal at the receiver output. A small
amount of input hysteresis is included to minimize the ef-
fects of noise on the line signals. If the line is terminated
or the receiver inputs are shorted together, the receiver
output will retain the last valid line signal due to the
45mV of hysteresis incorporated in the receiver circuit. If
the receiver inputs are left floating (unterminated), an in-
ternal pull-up of 10μA at the A input will force the re-
ceiver output to a guranteed high output state.
DRIVER OUTPUT STAGE
The RS-485 specification requires that a transceiver with-
stand common-mode voltages of up to 12V above or –7V
below system ground at the RS-485 line connections.
In addition, the transceiver must be protected against both
ESD and latch-up. This precludes the use of conventional
RECEIVING
INPUTS
OUTPUT
RE
D E
A-B
R O
0
X
0.2V
1
0
X
-0.2V
0
0
X
Open/shorted
1
1
0
X
Shutdown*
*In shutdown mode, driver and receiver outputs high impedance
PRELIMINARY TECHNICAL DATA
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1487JN | Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection |
| ADM1487JR | Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection |
| ADM1816-10ART-REEL | Microprocessor Reset Circuits |
| ADM1816-10ART-RL7 | Microprocessor Reset Circuits |
| ADM1816-20ART-REEL | Microprocessor Reset Circuits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1487E | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V, 【15 kV ESD Protected Half-Duplex, RS-485/RS-422 Transceivers |
| ADM1487EARZ | 功能描述:IC TXRX HALF DUP RS485/422 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| ADM1487EARZ-REEL7 | 功能描述:IC TXRX HALF DUP RS485/422 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:121 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:3 V ~ 3.6 V 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-DFN（3x3） 包裝:管件 |
| ADM1487JN | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Power RS-485/RS-422 Transceiver with Low EMI and +/-10kV ESD Protection |
| ADM1487JR | 制造商:Analog Devices 功能描述:LINE TRNSCVR 1TR 1TX 1RX 8SOIC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。