- 您現在的位置：買賣IC網 > PDF目錄16621 > ADM00310 (Microchip Technology)BOARD EVAL FOR MCP3903 AFE PDF資料下載
參數資料
| 型號： | ADM00310 |
| 廠商： | Microchip Technology |
| 文件頁數： | 41/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR MCP3903 AFE |
| 產品培訓模塊： | MCP3903 6-Channel Energy Measurement Analog Front End |
| 設計資源： | MCP3903 Eval Brd BOM MCP3903 Eval Brd Schematic |
| 標準包裝： | 1 |
| 主要目的： | 接口，模擬前端（AFE） |
| 嵌入式： | 是，MCU，16 位 |
| 已用 IC / 零件： | MCP3903，PIC24F，PIC24H，dsPIC33，MCP2200 |
| 已供物品： | 板，2 個模塊，線纜，CD，電源 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁
MCP2200
DS22228B-page 6
2011 Microchip Technology Inc.
1.5.2.1
Internal Power Supply Details
MCP2200 offers various options for power supply. To
meet the required USB signaling levels, MCP2200
device incorporates an internal LDO used solely by the
USB transceiver, in order to present the correct D+/D-
voltage levels.
Figure 1-2 shows the internal connections of the USB
transceiver LDO in relation with the VDD power supply
rail. The output of the USB transceiver LDO is tied to
the VUSB line. A capacitor connected to the VUSB pin is
required if the USB transceiver LDO provides the 3.3V
supply to the transceiver.
FIGURE 1-2:
MCP2200 INTERNAL
POWER SUPPLY DETAILS
The provided VDD voltage has a direct influence on the
voltage levels present on the GPIO pins (Rx/Tx and
RTS/CTS). When VDD is 5V, all of these pins will have
a logical ‘1’ around 5V with the variations specified in
For applications that require a 3.3V logical ‘1’ level,
VDD must be connected to a power supply providing
the 3.3V voltage. In this case, the internal USB trans-
ceiver LDO cannot provide the required 3.3V power. It
is necessary to also connect the VUSB pin of the
MCP2200 to the 3.3V power supply rail. This way, the
USB transceiver is powered up directly from the 3.3V
power supply.
1.5.2.2
USB Bus Powered (5V)
In Bus Power Only mode, all power for the application
is drawn from the USB (Figure 1-3). This is effectively
the simplest power method for the device.
FIGURE 1-3:
BUS POWER ONLY
In order to meet the inrush current requirements of the
USB 2.0 specifications, the total effective capacitance
appearing across VBUS and ground must be no more
than 10 F. If it is not more than 10 F, some kind of
inrush limiting is required. For more details on Inrush
Current Limiting, search for that subject in the current
Universal Serial Bus Specification
.
According to the USB 2.0 specification, all USB devices
must also support a Low-Power Suspend mode. In the
USB Suspend mode, devices must consume no more
than 500 A (or 2.5 mA for high powered devices that
are remote wake-up capable) from the 5V VBUS line of
the USB cable.
The host signals the USB device to enter Suspend
mode by stopping all USB traffic to that device for more
than 3 ms.
The USB bus provides a 5V voltage. However, the USB
transceiver requires 3.3V for the signaling (on D+ and
D- lines).
During USB Suspend mode, the D+ or D- pull-up
resistor must remain active, which will consume some
of
the
allowed
suspend
current
budget
(500 A/2.5 mA). The VUSB pin is required to have an
external bypass capacitor. It is recommended that the
capacitor be a ceramic cap, between 0.22 and 0.47 F.
Figure 1-4 shows a circuit where MCP2200’s internal
LDO is used to provide 3.3V to the USB transceiver.
The voltage on the VDD affects the voltage levels onto
the GPIO pins (Rx/Tx and RTS/CTS). With VDD at 5V,
these pins will have a logic ‘1’ of 5V with the variations
specified in Section 3.1, DC Characteristics.
LDO
3.3V
USB
Transceiver
D+
VDD
VUSB
D-
IN
OUT
VDD
VUSB
VSS
VBUS
相關PDF資料 |
PDF描述 |
|---|---|
| ELC-18B182L | COIL CHOKE 1800UH RADIAL |
| GBM36DRTH | CONN EDGECARD 72POS DIP .156 SLD |
| RCM12DRYF | CONN EDGECARD 24POS DIP .156 SLD |
| RBM12DRTF-S13 | CONN EDGECARD 24POS .156 EXTEND |
| M1BXA-4036J | IDC CABLE - MSR40A/MC40G/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM00313 | 功能描述:電源管理IC開發工具 73830L Li-Ion Battry Charger Eval Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| ADM00317 | 功能描述:數據轉換 IC 開發工具 MCP47X6 PICtail Plus Daughter Board RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| ADM00333 | 功能描述:開發板和工具包 - PIC / DSPIC PIC18F87J72 Evaluation Board RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| ADM00344 | 功能描述:電源管理IC開發工具 RE46C190 Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| ADM00345 | 功能描述:電源管理IC開發工具 3-Phase BLDC Snsrlss Fan Cntrllr RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。