- 您現在的位置：買賣IC網 > PDF目錄11215 > ADG2108YCPZ-REEL7 (Analog Devices Inc)IC CROSSPOINT SWIT 8X10 32LFCSP PDF資料下載
參數資料
| 型號： | ADG2108YCPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/28頁 |
| 文件大小： | 0K |
| 描述： | IC CROSSPOINT SWIT 8X10 32LFCSP |
| 產品培訓模塊： | Switch Fundamentals |
| 產品變化通告： | Interface Change Notice 12/Apr/2010 |
| 標準包裝： | 1 |
| 功能： | 交叉點開關 |
| 電路： | 1 x 8:10 |
| 導通狀態電阻： | 50 歐姆 |
| 電壓電源： | 單/雙電源 |
| 電壓 - 電源，單路/雙路(±)： | 12V，±15V |
| 電流 - 電源： | 50nA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-VQ（5x5） |
| 包裝： | 剪切帶 (CT) |
| 配用： | EVAL-ADG2108EBZ-ND - BOARD EVAL FOR ADG2108 |
| 其它名稱： | ADG2108YCPZ-REEL7CT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
Data Sheet
ADG2108
Rev. B | Page 19 of 28
SERIAL INTERFACE
The ADG2108 is controlled via an I2C-compatible serial bus.
The parts are connected to this bus as a slave device (no clock
is generated by the switch).
HIGH SPEED I2C INTERFACE
In addition to standard and full speed I2C, the ADG2108 also
supports the high speed (3.4 MHz) I2C interface. Only the -HS
models provide this added performance. See the Ordering
Guide for details.
SERIAL BUS ADDRESS
The ADG2108 has a 7-bit slave address. The four MSBs are
hard coded to 1110, and the three LSBs are determined by the
state of Pin A0, Pin A1, and Pin A2. By offering the facility to
hardware configure Pin A0, Pin A1, and Pin A2, up to eight
of these devices can be connected to a single serial bus.
The 2-wire serial bus protocol operates as follows:
1.
The master initiates data transfer by establishing a start
condition, defined as when a high-to-low transition on
the SDA line occurs while SCL is high. This indicates
that an address/data stream follows. All slave peripherals
connected to the serial bus respond to the start condition
and shift in the next eight bits, consisting of a 7-bit address
(MSB first) plus an R/W bit that determines the direction
of the data transfer, that is, whether data is written to or
read from the slave device.
2.
The peripheral whose address corresponds to the
transmitted address responds by pulling the SDA
line low during the ninth clock pulse, known as the
acknowledge bit. At this stage, all other devices on the
bus remain idle while the selected device waits for data
to be written to or read from its serial register. If the
R/W bit is 1 (high), the master reads from the slave
device. If the R/W bit is 0 (low), the master writes to
the slave device.
3.
Data is transmitted over the serial bus in sequences of
nine clock pulses: eight data bits followed by an acknowl-
edge bit from the receiver of the data. Transitions on the
SDA line must occur during the low period of the clock
signal, SCL, and remain stable during the high period of
SCL because a low-to-high transition when the clock is
high can be interpreted as a stop signal.
4.
When all data bits have been read or written, a stop
condition is established by the master. A stop condition
is defined as a low-to-high transition on the SDA line
while SCL is high. In write mode, the master pulls the
SDA line high during the 10th clock pulse to establish
a stop condition. In read mode, the master issues a no
acknowledge for the ninth clock pulse (that is, the SDA
line remains high). The master then brings the SDA line
low before the 10th clock pulse and then high during the
10th clock pulse to establish a stop condition.
Refer to Figure 33 and Figure 34 for a graphical explanation
of the serial data transfer protocol.
相關PDF資料 |
PDF描述 |
|---|---|
| ADG426BRSZ-REEL | IC MULTIPLEXER 16X1 28SSOP |
| ADG419TQ | IC SWITCH SPDT 8CDIP |
| VI-JWP-IW | CONVERTER MOD DC/DC 13.8V 100W |
| VE-J30-IW-F2 | CONVERTER MOD DC/DC 5V 100W |
| VI-BWT-IX | CONVERTER MOD DC/DC 6.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADG211 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(277.36 k) |
| ADG211A | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS QUAD SPST SWITCHES |
| ADG211A2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LC2MOS Quad SPST Switches(277.15 k) |
| ADG211AKN | 功能描述:IC SWITCH QUAD SPST 16DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:LC²MOS 標準包裝:1,000 系列:- 功能:多路復用器 電路:1 x 4:1 導通狀態電阻:- 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±5V 電流 - 電源:7mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ADG211AKNZ | 功能描述:IC SWITCH QUAD SPST 16DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:LC²MOS 特色產品:MicroPak? 標準包裝:1 系列:- 功能:開關 電路:2 x SPST - NC 導通狀態電阻:500 毫歐 電壓電源:單電源 電壓 - 電源，單路/雙路(±):1.4 V ~ 4.3 V 電流 - 電源:150nA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-XFDFN 供應商設備封裝:8-XSON，SOT833-1 （1.95x1） 包裝:Digi-Reel® 其它名稱:568-5557-6 |
發布緊急采購，3分鐘左右您將得到回復。